Download
Share
Print this page
SunSetter OASIS Replacement Instructions Manual
  1. Manuals
  2. Brands
  3. SunSetter Manuals
  4. Accessories
  5. Oasis
  6. Replacement instructions manual
SunSetter OASIS Replacement Instructions Manual

SunSetter OASIS Replacement Instructions Manual

Manual/motorized, roller bar
Hide thumbs Also See for OASIS:

Advertisement

Quick Links

Download this manual
For Motorized OASIS, use Section B, page 6.
Tools Needed: Stepladder, Sawhorses or Chairs, Hammer or Mallet, 9/16" Socket and Driver, 9/16" Wrench, and
a 5 mm Allen Wrench.
Parts Supplied: Replacement Roller Bar Assembly with (2)End Caps and (4) Plastic Safety Sleeves.
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!! PLEASE READ
THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO PERFORM THIS PROCEDURE.
1. Open Awning to the fully extended position.
2. On the end of the Awning opposite the Gear Assembly, locate the Front Bar Connectors that secure
the Lateral Arms to the Front Bars. Using a 5 mm Allen wrench loosen the inside bolt on the Front Bar
Connector on both of the Front Bars on that end of the awning. See Figure 1
Motor/Gear Assembly End
Front Bar
Connector
Lateral Arm
Note: If you can close your Awning using the Crank Wand, continue with Step 7.
If you cannot close your Awning using the Crank Wand, complete the following procedure (Steps 3 through
6), then continue with Step 9.
WARNING: MAKE SURE THAT NO ONE STANDS IN FRONT OF THE AWNING DURING THIS PROCEDURE, IN
CASE THE AWNING SPRINGS OPEN.
©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148
RETRACTABLE AWNINGS
For Technical Support visit us at www.sunsetter.com/ownerscorner
or Call Toll Free 800-670-7071 • Fax 877-224-4944
For Manual OASIS, use Section A, page 1.
Manual OASIS Awning
Roller Bar Replacement Instructions
*Helpers Needed*
Front Bar
Figure 1: Underside View
Section A
Front Bar
Inside Bolt
Front Bar Connector
Lateral Arm

Advertisement

loading
Need help?

Need help?

Do you have a question about the OASIS and is the answer not in the manual?

Questions and answers

Related Manuals for SunSetter OASIS

Summary of Contents for SunSetter OASIS

  • Page 1 If you cannot close your Awning using the Crank Wand, complete the following procedure (Steps 3 through 6), then continue with Step 9. WARNING: MAKE SURE THAT NO ONE STANDS IN FRONT OF THE AWNING DURING THIS PROCEDURE, IN CASE THE AWNING SPRINGS OPEN. ©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148...
  • Page 2 3. Position a step ladder at the Gear Assembly end of the Awning (Note: Outside the Awning, not under the Awning) and align with the Elbow of the left Lateral Arm Assembly. See Figure 2. 4. Starting with the left Lateral Arm Assembly, push in on the Elbow to start the Lateral Arm to close and grasp the outside edge of the Front Bar and pull it in toward the End Bracket.
  • Page 3 Figure 3 9. Position two (2) Sawhorses or Chairs approximately eight feet apart to support the top of the Awning in the following steps. See positioning in Figure 4. Figure 4 WARNING: THE FOLLOWING PROCEDURE SHOULD BE ACCOMPLISHED BY FOUR (4) PEOPLE 10.
  • Page 4 14. On the end of the Awning opposite the Gear Assembly, using a 9/16” socket and wrench, loosen and remove the two (2) bolts that secure the Corner Brace to the Horizontal Square Bar. See Figure 7. End opposite the Gear Assembly Horizontal Square Bar Top Bracket Assembly Remove these two (9/16”...
  • Page 5 WARNING: THE FOLLOWING PROCEDURE SHOULD BE ACCOMPLISHED BY FOUR (4) PEOPLE. 27. One person should be positioned at each Leg Assembly to prevent the OASIS Awning from sliding as the OASIS is placed in the upright position. 28. One person should be positioned at each end of the Awning Assembly, and be able to support and lift the weight of that end of the Awning.
  • Page 6 Section B Motorized Oasis Awning Roller Bar Replacement Instructions *Helpers Needed* Tools Needed: Step Ladder, Sawhorses or chairs, 7/16” Wrench, 9/16” Wrench and Socket with Driver. Parts Supplied: Roller Bar Assembly with two (2) End Caps and (4) Plastic Safety Sleeves.
  • Page 7 2. Unplug the Power Cord from your electrical outlet and, if installed, remove the Cord Cover from the Square Bar Upright. 3. Starting with the Left Arm Assembly, push in on the Elbow to start the Arm to close and grasp the outside edge of the Front Bar and pull it in toward the End Bracket.
  • Page 8 Motor End Cap with the Square Cord Pin (used with Manual One Bolt Do NOT OASIS) supplied with the to Remove Remove! Figure 8 (Re: Step 14) Replacement Roller Bar. 21. Orient the Replacement Roller Bar so the end of...
  • Page 9 Roller Bar, turn the Crank Wand counter clockwise to slowly roll the Fabric onto the Roller Bar. Facing the Motor end of the OASIS Awning, the Fabric should roll onto the Roller Bar, by rolling from the right side, over the Roller Bar.
  • Page 10 8. If the preceding steps do not allow moving the OPEN or STOP position setting to the correct position, follow the steps in Appendix A to completely reset the Motor’s Open and Close stop position settings. 9. For assistance resetting your Motor, please contact SunSetter at 800-670-7071.
  • Page 11 APPENDIX A Reset the Motor’s Open and Close Stop Positions WARNING: ALL STEPS MUST BE FOLLOWED EXACTLY AND COMPLETELY. PREPARE MOTOR Front View 1. Read these instructions FIRST, completely and thoroughly. 2. Press and Hold the my button; the red LED light should blink for at least 5 seconds. 3.
  • Page 12 A PLACE FOR YOUR NOTES SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA 02148 July 25, 2013 Oasis_RollerBar-Replacement...