Advertisement
www.Securitykala.com | 031-91003037 09133648641
Logic
Definition
Block pulses during
IBL OPEN
opening
Block pulses during
|IBL TCA
TCA
Block pulses during
IBL CLOSE
closing
OPEN IN OTHER
Open in other
direction
DIRECT.
Configuration of
SAFE 1
safety input SAFE 1.
72
Configuration of
SAFE 2
safety input SAFE 2.
74
Configuration of
SAFE 3
safety input SAFE 3.
77
Configuration of
IC 1
command input IC 1.
61
Configuration of
IC 2
command input IC 2.
62
Configuration of
IC 3
command input IC 3.
64
Configuration of
IC 4
command input IC 4.
65
AUX 3
Configuration of
AUX 3 output.
(Setup for
26-37
LEO B CBB 3 120 F02)
FIXED CODE
Fixed code
Transmitter pro-
RADIO PROG
gramming
INSTALLATION MANUAL
Cross out
Default
setting
used
0
Pulse from inputs configured as Start E, Start I, Ped has effect during opening.
0
1
Pulse from inputs configured as Start E, Start I, Ped has no effect during opening.
0
Pulse from inputs configured as Start E, Start I, Ped has effect during TCA pause.
0
1
Pulse from inputs configured as Start E, Start I, Ped has no effect during TCA pause.
0
Pulse from inputs configured as Start E, Start I, Ped has effect during closing.
0
1
Pulse from inputs configured as Start E, Start I, Ped has no effect during closing.
0
Standard operating mode (Fig.G Rif. 1).
0
1
Opens in other direction to standard operating mode (Fig. G Rif.2)
0
Input configured as Phot (photocell).
0
1
Input configured as Phot test (tested photocell).
2
Input configured as Phot op (photocell active during opening only).
3
Input configured as Phot op test (tested photocell active during opening only).
6
4
Input configured as Phot cl (photocell active during closing only).
5
Input configured as Phot cl test (tested photocell active during closing only).
6
Input configured as Bar, safety edge.
2
7
Input configured as Bar, tested safety edge.
8
Input configured as Bar 8k2 (Not active on SAFE 3).
0
Input configured as Start E.
0
1
Input configured as Start I.
2
Input configured as Open.
4
3
Input configured as Close.
4
Input configured as Ped.
2
5
Input configured as Timer.
3
6
Input configured as Timer Pedestrian.
0
Output configured as 2nd Radio Channel.
1
Output configured as SCA (gate open light).
2
Output configured as Courtesy Light command.
0
3
Output configured as Zone Light command.
4
Output configured as Stair Light
5
Output configured as Alarm
6
Output configured as Flashing light
Receiver is configured for operation in rolling-code mode.
0
Fixed-Code Clones are not accepted.
0
Receiver is configured for operation in fixed-code mode.
1
Fixed-Code Clones are accepted.
Disables wireless memorizing of transmitters.
Transmitters are memorized only using the relevant Radio menu.
0
IMPORTANT: This high level of security stops unwanted clones from gaining access and also
stops radio interference, if any
A- Enables wireless memorizing of transmitters:
Operations in this mode are carried out near the control panel and do not require access:
- Press in sequence the hidden key and normal key (T1-T2-T3-T4) of a transmitter that has already
1
been memorized in standard mode via the radio menu.
- Press within 10 sec. the hidden key and normal key (T1-T2-T3-T4) of a transmitter to be memorized.
1
The receiver exits programming mode after 10 sec.: you can use this time to enter other new
transmitters by repeating the previous step
B-Enables wireless automatic addition of clones and replays.
Enables clones generated with the universal programmer and programmed replays to be added to
the receiver's memory.
Optional extras
LEO B CBB 3 230 L02/L04 - LEO B CBB 3 120 F02 / F04
27
-
Advertisement
