Attenzione! Leggere attentamente le "Avvertenze" all'interno! Caution! Read "Warnings" inside carefully! Attention! Veuillez lire attentivement les Avertissements qui se trouvent à l'intérieur! Achtung! Bitte lesen Sie
aufmerksam die „Hinweise" im Inneren! ¡Atención¡ Leer atentamente las "Advertencias" en el interior! Let op! Lees de "Waarschuwingen"tigre aan de binnenkant zorgvuldig!
Page 1
QUADRO COMANDO CONTROL PANEL CENTRALE DE COMMANDE SELBSTÜBERWACHENDE STEUERUNG CUADRO DE MANDOS BEDIENINGSPANEEL Attenzione! Leggere attentamente le “Avvertenze” all’interno! Caution! Read “Warnings” inside carefully! Attention! Veuillez lire attentivement les Avertissements qui se trouvent à l’intérieur! Achtung! Bitte lesen Sie aufmerksam die „Hinweise“ im Inneren! ¡Atención¡ Leer atentamente las “Advertencias” en el interior! Let op! Lees de “Waarschuwingen”tigre aan de binnenkant zorgvuldig!
START 24 VSafe+ Accessories power supply 24V + 24V - SW02 SWC2 SW01 Limit switch inputs SWC1 Solenoid lock 24V-max15W Blinker max 25W Motor F1 1.25 AT (220-230V) F1 2.5 AT (120V) Other voltages available on request - ZARA BTL2...
Page 3
LEGENDA - KEY - LÉGENDE - LEGENDE - LEYENDA - LEGENDA Steadily lit Continuous flashing Intermittent flashing ADJUSTING AUTOSET AUTO OPEN AUTO CLOSE AUTO OPEN AUTO CLOSE - After adjusting the end stops or modifying their position, a new autoset cycle must be performed. ZARA BTL2...
Page 4
1 PHOT / 1 PHOT CL 1 BAR Bar 1 Bar 1 2 PHOT / 2 PHOT CL 2 BAR Bar 1 Bar 1 Bar 2 Bar 2 BAR 8K2 SAFETY EDGE SAFETY EDGE 8,2Kohm 5% BAR 8K2 - ZARA BTL2...
THE DECLARATION OF CONFORMITY CAN bE vIEWED ON THIS WEbSITE: WWW.bFT.IT IN THE PRODUCT SECTION. - Only use original spare parts for any maintenance or repair work. The Firm dis- claims all responsibility for the correct operation and safety of the automated system if parts from other manufacturers are used.
Page 6
INSTALLATION MANUAL 1) GENERAL INFORMATION Flashing light max. 25W The ZARA BTL2 control panel comes with standard factory settings. Any change must be set by means of the TRIMMER and DIP SWITCH settings. see Fig. C Fuses The Control unit completely supports the EELINK protocol.
Unlit: motor 2 opening limit switch input activated ted, hold down S2 for 5s to confirm. Unlit: no error NOTE: In any case, the Autoset fun- LIT: see error diagnostics table ction confirms all changes made to the board. - 11 ZARA BTL2...
Page 8
Thus the rod continues its stroke for a few seconds after meeting the closing limit switch or as far as the mechanical stop. In this way, the leaves come to rest perfectly against the stop by allowing the closing limit switches to trip slightly earlier (Fig.G Ref.A). - ZARA BTL2...
(where fitted). pendant son fonctionnement. - If any part of the automated system requires direct - Empêcher les enfants de jouer ou de stationner dans le rayon d’action de l’automatisation. AVVERTENZE PER L’UTILIZZATORE D811767_05 - ZARA BTL2...
Need help?
Do you have a question about the ZARA BTL2 and is the answer not in the manual?
Questions and answers