Program Play - Yamaha EMX-100CD Owner's Manual

COMPACT DISC PLAYER OPERATION
CD CHANGER RECEIVER EMX–100CD
DISC
1 2
POWER
PHONES
1
1
6
6
A
TIME
TIME
MODE
DISC SKIP
2
CENTER/REAR
/DELAY
ECHO
3
SLEEP
Display information during programming
TAPE 1
PROGRAM USER
OGIC HALL
TRACK
Playback order
Music calendar
TAPE 1
ROGRAM USER
OGIC HALL
TRACK
Selected track number
1
INPUT SELECTOR
VCR/LD-TV/CD/TUNER/TAPE•MD/AUX
OPEN/
CLOSE
DISC
CHANGE
3
RANDOM REPEAT
PROGRAM
HOUR
PRESET/TUNING/BAND
MUSIC
ECHO ECHO
DISPLAY
USER MEMORY
CD
2 3 4 5
2 3 4 5
4
7 8 PRESET
7 8 9 0
B C D E
+
PROG I0
REPEAT RANDOM OPEN/CLOSE TUNER
1
STOP PLAY/PAUSE
INPUT
TEST FLAT
6
MUSIC PROGRAM USER
LEVEL
POWER
DISPLAY
VOLUME
1 2 3 4 5 6
7 8 9 10 11 12
13 14 15 OVER 15
PROG
Selected disc
1 2 3 4 5 6
7 8 9 10 11 12
TOTAL
13 14 15 OVER 15
PROG
Total playing time

Program play

You can program up to 20 tracks in any desired order.
1
Load discs and close the disc table.
2
VOLUME
When in the stop mode, press the PROG button to
prepare for programming.
* "PROG" and "P-01" will light up on the display, and all
TIME MEMORY AUTO/MAN'L track numbers on the selected disc begin flashing.
MIN TIME ADJ TIMER
A/B/C/D/E
3
If necessary, select a desired disc by pressing the DISC
MIC MIC MIXING
MIN MAX
SKIP button.
* Just after you changes the disc, this unit reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
6 step, "WAIT" appears on the display and your
operation is canceled.
4
Use the track number input buttons to select the desired
track number.
* The selected track number and the total play time of
the programmed tracks will light up on the display, and
soon it is replaced by the display of the next playback
order. Programmed track numbers on the selected disc
will stop flashing and light up on the music calendar.
* Pressing the TIME button displays the total play time of
the programmed tracks for about 1 second, and then it
is replaced by the display of the next playback order.
* For example, to choose selection 12
(1) Press the "+10" button.
(2) Within 3 seconds, press the "2" button.
5
Repeat steps 3 and 4 for any other track. Up to 20 tracks
can be programmed.
6
Press the play/pause
programmed tracks.
Notes
•
It is also possible to program a sequence of tracks while
looking at the list of tracks on the surface of the disc
before closing the disc table.
•
During playback or pause, programming is not possible.
•
If the total time of the programmed tracks becomes 100
minutes or more, the highest position of a figure will not be
displayed.
•
The total time of the programmed tracks will not be
VOLUME
displayed, if track number 16 or higher is programmed.
•
Skip search can be performed during playback, but only
within the range of the programmed tracks.
•
Manual search can be performed during playback to
search all tracks, including unprogrammed tracks.
•
If programs are made selecting tracks from more than one
disc, pressing the DISC CHANGE button is useless during
program play.
VOLUME
E-16
/ button to start playback of