Related Manuals for SKF PAB Series
Summary of Contents for SKF PAB Series
- Page 1 Original assembly instructions with associated Product designation operating instructions acc. to EC Machinery Directive Centrifugal pump 2006/42/EC Product series: PAB… / PNB… Version 02...
-
Page 2: Masthead
Tel. +49 (0)30 72002-0 VDI 4500. Fax +49 (0)30 72002-261 © SKF Lubrication Systems Germany GmbH spandaupumpen@skf.com This documentation is protected by copyright. SKF www.spandaupumpen.de Lubrication Systems Germany GmbH reserves all rights, including those to the photomechanical reproduction, duplication, and distribution by means of special procedures (e.g., data processing,... -
Page 3: Table Of Contents
2. Pumped media 11.3 Mechanical design 3. Assemblies and type designation 11.4 Characteristic curves for 50Hz or 60Hz 3.1 PAB series with impeller change - PAB 3.2 PNB series 11.5 Electrical values for PAB 4. -
Page 4: Information Concerning Ec Declaration Of
Low Voltage Devices 2014/35/EU Annex II Part B, designed for installation in machinery / for incorporation with other the products supplied by SKF Lubrication Systems Electromagnetic Compatibility 2014/30/EU machinery to form a machine. Within the Germany GmbH do not reach the limit values listed ... -
Page 5: General Information
General information Page 5 General information Instructions attached directly to the equipment, Explanation of symbols and signs such as rotational direction arrows and fluid You will find these symbols, which warn of specific connection labels, must be followed. Replace such dangers to persons, material assets, or the signs if they become illegible. - Page 6 Page 6 Original assembly instructions Product designation acc. to EC Machinery Directive 2006/42/EC Centrifugal pump Product series: PAB… / PNB…...
-
Page 7: Safety Instructions
The operator of the described product must ensure that the approved by SKF Lubrication Systems Germany They are designed for vertical installation. GmbH. assembly instructions are read and understood by all persons tasked... -
Page 8: Authorized Personnel
Unless specially indicated otherwise, products All instructions placed directly on the from SKF Lubrication Systems Germany GmbH pump regarding direction of are not approved for use in potentially rotation, dry running, bypass explosive areas as defined in the ATEX Directive connection, and the rating plate 2014/34/EU. -
Page 9: Electric Shock Hazard
1. Safety instructions Page 9 Alteration and repair work may only Performing work on products that be performed by persons possessing have not been de-energized may 1.3 Electric shock hazard the knowledge and certifications result in serious injury or death. required for the potentially explosive Assembly, maintenance, and repair Electrical connections for the described product... -
Page 10: Hydraulic Pressure Hazard
during operation. Maintenance and repair work performed improperly or not performed at all Use of non-original SKF spare parts Alterations or modifications performed without written approval from SKF Lubrication Systems Germany GmbH Non-compliance with the instructions for... -
Page 11: Hazard From Hazardous Or Dangerous Substances
2. Pumped media Page 11 1.7 Hazard from hazardous or 2. Pumped media dangerous substances Safety measures must be taken Solvent-based inks The requirements specified above according to the parameters of the Varnishes and oil-based paints must be met by level monitoring media in use, especially in the case Water-based paints ... -
Page 12: Assemblies And Type Designation
3. Assemblies and type designation Page 12 3. Assemblies and type designation Pumps of the PAB and PNB series comply with Spandau immersion pumps of the PAB and PNB series are available in various sizes which the harmonized standards EN 13463-1 and EN Explosion protection class 13463-5. -
Page 13: Pab Series
3. Assemblies and type designation Page 13 3.1 PAB series The PAB pump series has a design allowing the pump and the motor component to be separated for better handling. PAB pump Type code components can only be operated with PAB Designation motor components. -
Page 14: Design And Function
Pumps of the PAB and PNB series have the same basic design, the only difference being that the pump port on the PAB series can be separated from the drive motor. In this series, both shaft ends (pump/motor) are connected via a coupling (Figure 1, right). -
Page 15: Assembly Instructions
5. Assembly instructions Page 15 During all assembly work on machinery, When operating the pump, it must be ensured 5. Assembly instructions observe the local accident prevention that the lowest permissible fluid level is above regulations as well as the applicable operating the lowest pump chamber. - Page 16 "Technical data." the pump. customer documentation directly from SKF Lubrication Systems Germany GmbH. The pump is equipped with a 4-hole connecting flange with standard port dimensions (see "Technical data") for assembly. The screw connections must be permanently secured against loosening.
-
Page 17: Port Dimensions
5. Assembly instructions Page 17 5.2 Port dimensions 5.4 Pipe connection The lines must be connected in such a way See the "Technical data" chapter. Connect the pipes to the provided connection that no forces are transferred to the pump port on the pump port. -
Page 18: Electrical Connection
5. Assembly instructions Page 18 5.6 Electrical connection Establish the connection in accordance with the If a pump/motor has been stored unused for an Electrical connections for the pump relevant regulations and standards as well as extended time, it is recommended that the may only be established by qualified insulation resistance of the winding against the the conditions for connections contained in... - Page 19 5. Assembly instructions Page 19 5.7 Motor protection 5.8 Direction of rotation a) Devices for direct temperature monitoring Electrical machines must be The direction of motor rotation must match the using thermistors (Figure 4). protected against excessive heating arrow on the pump. To check the direction of resulting from overload.
-
Page 20: Operating Instructions
Operating instructions Page 20 Operating instructions Product designation Centrifugal pump Product series: PAB… / PNB…... -
Page 21: Transport, Delivery, And Storage
6.3 General notes storage The product(s) can be enveloped in plastic film Ensure that the storage SKF Lubrication Systems Germany GmbH products to provide low-dust storage. Protect against ground moisture by storing on environment is dry, dust-free and are packaged in accordance with standard low-vibration (veff ... -
Page 22: Operation And Commissioning
7. Operation and commissioning Page 22 Bring the pump into operation as follows: further during pump operation to prevent the 7. Operation and pump from running dry. Completely open the pressure-side shutoff commissioning A backflow preventer is recommended for high delivery heads, long pipes, and pumps in suction valve (if present) or ensure that the connection operation. -
Page 23: Shutdown
"General information" chapter in these disposal of lubricants. assembly instructions must be observed when doing so. The product can also be returned to SKF Lubrication Systems Germany GmbH for disposal, To recommission the product, follow the in which case the customer is responsible for instructions in the "Assembly instructions"... -
Page 24: Maintenance
9. Maintenance Page 24 Touching the rotating impeller during Cables and lines must be inspected for damage 9. Maintenance startup, shutdown, trial run, setup, and secure electrical connection at regular fault-finding, fault resolution, intervals. 9.1 General notes maintenance, or inspection can result in severe injury. -
Page 25: Spare Parts
Explosion protection is voided if warranty. replacement is performed improperly. SKF Lubrication Systems Germany GmbH shall not 9.4 Modifications and rework be held liable for damages resulting from improperly performed assembly, maintenance or repair work on the product. -
Page 26: Malfunctions
Lubrication Systems Germany GmbH may be used. Unauthorized alterations causes. Contact the Service department of SKF Lubrication Systems Germany GmbH if you cannot to products and the use of non-original remedy the malfunction. - Page 27 10. Malfunctions Page 27 Fault analysis and rectification Malfunction Possible cause Rectification Motor does not start Power connection defective Check the power connection Fuse tripped Check the fuse or the motor circuit breaker Motor circuit breaker tripped Ensure that: The pump shaft runs smoothly and evenly ...
- Page 28 10. Malfunctions Page 28 Continuation of Fault analysis and rectification Malfunction Possible cause Rectification Motor circuit breaker is triggered Motor circuit breaker set too low Set the motor circuit breaker to the value specified on the rating plate and ensure that occasionally the pump is not overloaded Power supply not constant...
- Page 29 10. Malfunctions Page 29 Continuation of Fault analysis and rectification Malfunction Possible cause Rectification Noises, vibrations, or leaks Shaft seal defective Replace shaft seal Endplay of pump incorrect Set endplay Pump not mounted securely Fasten connecting flange Pump shaft rotates with difficulty Pump jammed Check the intake opening and clean it if necessary Impeller scrapes/rubs...
-
Page 30: Technical Data
The drive can therefore be separated shield below from the pump component without having to bottom ball be electrically disconnected. Cleaning is simpler bearing and faster as a result. All components of the -flange-type end PAB series are machine-washable. shield above top ball bearing... -
Page 31: Characteristic Curves For 50Hz Or 60Hz With Impeller Change - Pab
11. Technical data Page 31 11.4 Characteristic curves for 50Hz or 60Hz with impeller change - PAB... -
Page 32: Electrical Values For Pab
11. Technical data Page 32 11.5 Electrical values for PAB Type Frequency Motor Rated Motor Rated Starting Power index speed Type current [A] at factor factor 230V 400V [Hz] [kW] [min cosφ 265V 460V PAB05-XD 0.37 2830 0.93 0.84 ADCF71 PAB07-XD 0.44 3380... -
Page 33: Dimensions And Weights For Pab
11. Technical data Page 33 11.6 Dimensions and weights for Type Immer Weight Dimensions [mm] approx. depth Øm Øa Øb Ød Øe Øf Øq [kg] t[mm] -0.2 PAB0 5-XD PAB0 x1.5 7-XD PAB0 8-XD G1¼ PAB1 x1.5 1-XD PAB2 G1¼ 0-XD x1.5... -
Page 34: Characteristic Curves For 50Hz Or 60Hz With Impeller Change - Pnb
11. Technical data Page 34 11.7 Characteristic curves for 50Hz or 60Hz with impeller change - PNB... -
Page 35: Electrical Values For Pnb
11. Technical data Page 35 11.8 Electrical values for PNB Type Frequency Motor Rated Motor Rated Starting Power index speed Type current [A] at factor factor 230V 400V [Hz] [kW] [min cosφ 265V 460V PNB05-XD 0.37 2830 0.93 0.84 ADCF71 PNB07-XD 0.44 3380... -
Page 36: Dimensions And Weights For Pnb
11. Technical data Page 36 11.9 Dimensions and weights for Type Immers. Weight Dimensions [mm] depth approx. Øm Øa Øb Ød Øe Øf t[mm] [kg] PNB05- M25x1.5 PNB07- PNB34- M25x1.5... -
Page 37: Notes
12. Notes Page 37 12. Notes... - Page 38 Subject to change without notice. The contents of this publication are the copyright of the publisher and may not be reproduced in whole or in part without permission of SKF Lubrication Systems Germany GmbH. Every care has been taken to ensure the accuracy of the information contained in this publication. However, no liability can be accepted for any loss or damage, whether direct, indirect, or consequential, arising out of use of the information contained herein.
Need help?
Do you have a question about the PAB Series and is the answer not in the manual?
Questions and answers