Mitsubishi Electric FR-A800 Series Beginner's Manual page 83

Appendix
Param-
Name
eter
Second motor low-speed
747 range torque
characteristic selection
Second PID action
753
selection
Second PID control
754 automatic switch-over
frequency
Second PID action set
755
point
Second PID proportional
756
band
757 Second PID integral time
Second PID differential
758
time
759 PID unit selection
Pre-charge fault
760
selection
761 Pre-charge ending level
762 Pre-charge ending time
Pre-charge upper
763
detection level
764 Pre-charge time limit
Second pre-charge fault
765
selection
Second pre-charge
766
ending level
Second pre-charge
767
ending time
Second pre-charge
768
upper detection level
Second pre-charge time
769
limit
Operation panel monitor
774
selection 1
Operation panel monitor
775
selection 2
Operation panel monitor
776
selection 3
Frequency Inverters - Beginner's Guide
Setting Range Initial Value
0, 9999 9999
0, 10, 11, 20, 21,
50, 51, 60, 61, 70,
71, 80, 81, 90, 91,
100, 101, 1000, 0
1001, 1010, 1011,
2000, 2001, 2010,
2011
0–590 Hz,9999 9999
0–100 %,9999 9999
0.1–1000 %,9999 100%
0.1–3600 s,9999 1 s
0.01–10.00 s,
9999
9999
0–43, 9999 9999
0, 1 0
0–100 %, 9999 9999
0–3600 s, 9999 9999
0–100 %, 9999 9999
0–3600 s, 9999 9999
0, 1 0%
0–100 %,9999 9999
0–3600 s, 9999 9999
0–100 %,9999 9999
0–3600 s,9999 9999
9999
1–3, 5–14, 17–20,
22–35, 38, 40–45,
50–57, 61, 62, 64,
67, 87–98, 100,
9999
9999
9999
Param-
Name
eter
4mA input fault
777
operation frequency
778 4mA input check filter
Operation frequency
779 during communication
error
Low speed range torque
788
characteristic selection
Acceleration time in low-
791
speed range
Deceleration time in low-
792
speed range
Pulse increment setting
799
for output power
Control method
800
selection
802 Pre-excitation selection
Constant output range
803 torque characteristic
selection
Torque command source
804
selection
Torque command value
805
(RAM)
Torque command value
806
(RAM, EEPROM)
807 Speed limit selection
Forward rotation speed
808
limit/speed limit
Reverse rotation speed
809 limit/reverse-side speed
limit
Torque limit input
810
method selection
811 Set resolution switchover
Torque limit level
812
(regeneration)
Torque limit level (3rd
813
quadrant)
Torque limit level (4th
814
quadrant)
815 Torque limit level 2
Torque limit level during
816
acceleration
Torque limit level during
817
deceleration
Easy gain tuning
818
response level setting
Easy gain tuning
819
selection
820 Speed control P gain 1
Speed control integral
821
time 1
822 Speed setting filter 1
823 Speed detection filter 1
Parameter list (FR-A800)
Setting Range Initial Value
0–590 Hz, 9999 9999
0–10 s 0
0–590 Hz,9999 9999
0, 9999 9999
0–3600 s, 9999 9999
0–3600 s, 9999 9999
0.1, 1, 10, 100,
1 kWh
1000kWh
0–6, 9–14, 20,
100–106, 20
109–114
0, 1 0
0, 1, 10, 11 0
0, 1, 3–6 0
600–1400 % 1000 %
600–1400 % 1000 %
0–2 0
0–400 Hz 60/50 Hz
0–400 Hz, 9999 9999
0, 1 0
0, 1, 10, 11 0
0–400 %, 9999 9999
0–400 %, 9999 9999
0–400 %, 9999 9999
0–400 %, 9999 9999
0–400 %, 9999 9999
0–400 %, 9999 9999
1–15 2
0–2 0
0–1000 % 60 %
0–20 s 0.333 s
0–5 s, 9999 9999
0–0.1 s 0.001 s
A - 11