Mitsubishi Electric FR-A800 Series Beginner's Manual page 77

Appendix
Param-
Name
eter
RUN terminal function
190
selection
SU terminal function
191
selection
IPF terminal function
192
selection
OL terminal function
193
selection
FU terminal function
194
selection
ABC1 terminal function
195
selection
ABC2 terminal function
196
selection
232– Multi-speed setting
239 (speeds 8 to 15)
Soft-PWM operation
240
selection
Analog input display unit
241
switchover
Terminal 1 added
242 compensation amount
(terminal 2)
Terminal 1 added
243 compensation amount
(terminal 4)
Cooling fan operation
244
selection
245 Rated slip
Slip compensation time
246
constant
Constant-power range
247 slip compensation
selection
Self power management
248
selection
Earth fault detection at
249
start
Frequency Inverters - Beginner's Guide
Setting Range Initial Value
0–8, 10–20, 22,
0
25–28, 30–36,
38–54, 56, 57, 60,
61, 63, 64, 68, 70,
79, 84, 85, 90
to99, 100–108,
110–116, 120,
122, 125–128,
130–136,
138–154, 156,
157, 160, 161,
163, 164, 168,
170, 179, 184,
185, 190–199,
200–208,
300–308,
9999
1
2/9999/2
3
4
99
9999
0–590 Hz, 9999 9999
0, 1 1
0, 1 0
0–100 % 100 %
0–100 % 75 %
0, 1, 101–105 1
0–50 %, 9999 9999
0.01–10 s 0.5 s
0, 9999 9999
0–2 0
0, 1 0
Param-
Name
eter
250 Stop selection
Output phase loss
251
protection selection
252 Override bias
253 Override gain
Main circuit power OFF
254
waiting time
255 Life alarm status display
Inrush current limit
256
circuit life display
Control circuit capacitor
257
life display
Main circuit capacitor life
258
display
Main circuit capacitor life
259
measuring
PWM frequency
260
automatic switchover
Power failure stop
261
selection
Subtracted frequency at
262
deceleration start
Subtraction starting
263
frequency
Power-failure
264
deceleration time 1
Power-failure
265
deceleration time 2
Power failure
266 deceleration time
switchover frequency
Terminal 4 input
267
selection
Monitor decimal digits
268
selection
269 Parameter for manufacturer setting. Do not set.
Stop-on contact/load
torque high-speed
270
frequency control
selection
High-speed setting
271
maximum current
Middle-speed setting
272
minimum current
273 Current averaging range
Current averaging filter
274
time constant
Stop-on contact
275 excitation current low-
speed multiplying factor
PWM carrier frequency at
276
stop-on contact
278 Brake opening frequency
Parameter list (FR-A800)
Setting Range Initial Value
0–100 s,
1000–1100 s, 9999
8888, 9999
0, 1 1
0–200 % 50 %
0–200 % 150 %
0–3600 s, 9999 600 s
(0–15) 0
(0–100 %) 100 %
(0–100 %) 100 %
(0–100 %) 100 %
0, 1 0
0, 1 1
0–2, 21, 22 0
0–20 Hz 3 Hz
0–590 Hz, 9999 60/50 Hz
0–3600 s 5 s
0–3600 s, 9999 9999
0–590 Hz 60/50 Hz
0–2 0
0, 1, 9999 9999
0–3, 11, 13 0
0–400 % 50 %
0–400 % 100 %
0–590 Hz, 9999 9999
1–4000 16
50–300 %, 9999 9999
0–9, 9999 /
9999
0–4, 9999
0–30 Hz 3 Hz
A - 5