Related Manuals for Smarteh LPC-2.WT1
Summary of Contents for Smarteh LPC-2.WT1
- Page 1 USER MANUAL Longo programmable controller LPC-2.WT1 Wireless Light Switch Control panel Version 4 SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: +386(0)5 388 44 00 / e-mail: info@smarteh.si / www.smarteh.si...
- Page 2 Longo programmable controller LPC-2.WT1 Written by SMARTEH d.o.o. Copyright © 2017, SMARTEH d.o.o. User Manual Document Version: 4 January, 2017...
- Page 3 24 months is valid from the date of sale to the end buyer, but not more than 36 months after delivery from Smarteh. In case of claims within warranty time, which are based on material malfunctions the producer offers free replacement. The method of return of malfunctioned module, together with description, can be arranged with our authorized representative.
-
Page 4: Table Of Contents
Longo programmable controller LPC-2.WT1 Longo programmable controller LPC-2.WT1 1 ABBREVIATIONS................1 2 DESCRIPTION...................2 3 FEATURES..................3 4 OPERATION..................4 4.1 Operational modes..............4 4.2 Parameters................4 5 INSTALLATION..................7 5.1 Connection scheme..............7 5.2 Service mode................9 5.3 Mounting frame selection............10 5.4 Mounting instructions..............11 5.5 Module labeling...............12 6 TECHNICAL SPECIFICATIONS..............13 7 SPARE PARTS..................14... -
Page 5: Abbreviations
Longo programmable controller LPC-2.WT1 1 ABBREVIATIONS Sorted by order of appeareance in document: Push button Liquid crystal display Dual in-line package Set point WM-BUS Wireless M-Bus... -
Page 6: Description
Longo programmable controller LPC-2.WT1 2 DESCRIPTION LPC-2.WT1 wireless light switch control panel is used to switch on/off four individual or group of lights. Panel is equipped with four push buttons (PB), temperature, humidity and light intensity sensor. Data are displayed on low power monochromatic LCD. -
Page 7: Features
Longo programmable controller LPC-2.WT1 3 FEATURES Figure 1: LPC-2.WT1 wireless panel. Table 1: Features Wireless temperature and humidity measurement 4 touch buttons to switch light on/off 4 light symbols to show lights on/off status Light intensity measurement for smart LCD on/off regulation Up to 30 meters indoor signal range Depends of the RF output signal configuration. -
Page 8: Operation
LPC Tester. This is done by setting Service mode to "0" in RAM2. Service mode is enabled for 3 sec. after power up. If service mode is not triggered using Smarteh LPC Tester, then wireless panel will start in normal mode. - Page 9 Longo programmable controller LPC-2.WT1 enabled using oLight2_rem (Local/Remote) command. Type: BOOL → Raw to engineering data: “0” Light “OFF” → “1” Light “ON” Light 1_On (Off/On) [oLight1_On]: Remote on/off command for light1. This command is enabled using oLight1_rem (Local/Remote) command.
- Page 10 Longo programmable controller LPC-2.WT1 → Raw to engineering data: “0” Light “OFF” → “1” Light “ON” Light 1_On (Off/On) [iLight1_On]: When status is active, command for light 1 is requested and symbol “ON” is present on LCD screen. Type: BOOL →...
-
Page 11: Installation
Longo programmable controller LPC-2.WT1 5 INSTALLATION 5.1 Connection scheme Figure 2: Connection scheme to main module... - Page 12 Longo programmable controller LPC-2.WT1 Table 2: K1 K1.1 Ground K1.2 7 .. 15 V DC Power supply input K1.3 RS-232 Rx Data receive line K1.4 RS-232 Tx Data transmit line Table 3: LCD screen symbols & buttons Switch light 1 on/off, status is shown on LCD next to...
-
Page 13: Service Mode
In service mode LPC-2.WT1 is connected to PC via Smarteh LSA-2.USB adapter. Connection between LPC-2.WT1 and LSA-2.USB is made with SMB programming cable which is connected to K1 connector on LPC-2.WT1 and RS-232 port on LSA-2 USB adapter. Service mode must only be entered by a qualified technician. -
Page 14: Mounting Frame Selection
Longo programmable controller LPC-2.WT1 5.3 Mounting frame selection Wireless panel casing is designed to be used as remotely panel allowing users to move it or use it as a wall mounted panel on fixed place. Wall mounting procedure: Cut off circular shape at the back of the case with the knife cutter, •... -
Page 15: Mounting Instructions
Panel is designed to be installed or placed vertically allowing air flow from bottom to top. 1. Set the correct subnet (S1 switch) and wireless panel address (S2 switch) inside LPC-2.WT1 (refer to the Table 4 and Table 5), 2. Mount the back plate in mounting frames (dose), 3. -
Page 16: Module Labeling
Label 2 descriptions: 1. S/N: WT1-S9-1000000190 is the serial number. WT1 – short product name, • S9 – user code (test procedure, e.g. Smarteh person xxx), • 1000000190 – year and current stack code, • 10 – year (last two cyphers), •... -
Page 17: Technical Specifications
Longo programmable controller LPC-2.WT1 6 TECHNICAL SPECIFICATIONS Table 6: Technical specifications Power supply 2pcs. AA (LR6) battery Battery lifetime Approximately 1.5 years Operating frequency 868 Mhz Wireless protocol WM-Bus WM-Bus UID Power consumption Less than 0.1 W Dimensions (W x H x D) 75 ×... -
Page 18: Spare Parts
Longo programmable controller LPC-2.WT1 7 SPARE PARTS For ordering spare parts following Part Numbers should be used: LPC-2.WT1 light switch panel, wireless LPC-2.WT1 P/N: 225WT112001001 Programming cable SMB P/N: 203SMB14001001 LPC-2.WA1 wireless adapter LPC-2.WA1 P/N: 225WA112001001 Interconnection cable ICM-x P/N: 203ICMxxxxxxxx... -
Page 19: Changes
Longo programmable controller LPC-2.WT1 8 CHANGES The following table describes all the changes to the document. Date Description 15.01.17 Technical data update. 30.08.16 General update. 01.12.14 The initial version, issued as LPC-2.WT1 User Manual. -
Page 20: Notes
Longo programmable controller LPC-2.WT1 9 NOTES...
Need help?
Do you have a question about the LPC-2.WT1 and is the answer not in the manual?
Questions and answers