Related Manuals for Rittal DK 7859.312
Summary of Contents for Rittal DK 7859.312
- Page 1 PSM MID measuring module for CMC III DK 7859.312 DK 7859.332 Montage-, Installations- und Bedienungsanleitung Assembly and operating instructions...
- Page 2 35745 Herborn Germany Tel.: +49 (0)2772 / 505-0 Fax: +49 (0)2772 / 505-2319 E-mail: info@rittal.de www.rittal.com www.rittal.de We are always happy to answer any technical ques- tions regarding our entire range of products. Rittal PSM MID measuring module for CMC III...
-
Page 3: Table Of Contents
7.4.4 Messages on the main display ......14 Operation of the CMC III Processing Unit from the web site ........14 7.5.1 Device ............... 14 7.5.2 Circuit 1 ............. 14 7.5.3 Circuit 2 ............. 17 Rittal PSM MID measuring module for CMC III... -
Page 4: Notes On Documentation
1 Notes on documentation Notes on documentation CE labelling Rittal GmbH & Co. KG confirms the conformity of the PSM MID measurement module with EU-EMC regula- tion 2004/108/EU and with EU directive 2004/22/EU for measuring units. An appropriate declaration of conformity has been prepared. -
Page 5: Safety Instructions
Please also observe any company-internal regula- tions, such as work, operating and safety regula- tions. – Use only original Rittal products or products recom- mended by Rittal in conjunction with the PSM MID measuring module. – Please do not make any changes to the PSM MID measuring module that are not described in this manual or in the associated manuals. -
Page 6: Product Description
The intended use also includes the observance of the documentation provided and fulfilling the inspection and maintenance conditions. Rittal GmbH & Co. KG is not responsible for any dam- age which may result from failure to comply with the documentation provided. This also applies to failure to comply with the valid documentation for the used ac- cessories. -
Page 7: Transportation And Handling
Note: Damage and other faults, e.g. incomplete delivery, should immediately be reported to the shipping company and to Rittal GmbH & Co. KG in writing. Remove the unit from the packaging. Rittal PSM MID measuring module for CMC III... -
Page 8: Assembly And Siting
Fasten the PSM MID measuring module as shown in fig. 2 with the screws provided in a free slot (1 U) of the server enclosure. Fig. 2: Mounting on the enclosure frame Rittal PSM MID measuring module for CMC III... -
Page 9: Installation
Depending on the PSM MID measuring module var- CAN bus connection iant, a back-up fuse of 3 x 16 A (for model number CAN bus connection DK 7859.312) or 3 x 32 A (for model number "Infeed 2" connection DK 7859.332) should be provided. "Consumer 2" connection For connection of the PSM MID measuring module, 6.3.1... -
Page 10: Connection Of Two Consumers
Disp. Circuit setting in the configuration menu to "Source 1 + 2" (see section 7.4.1 "Settings using the con- figuration menu"). Rittal PSM MID measuring module for CMC III... -
Page 11: Operation
They display the status of the CAN bus. Colour Status The PSM MID measuring module is ini- tialised or an incorrect connection cable is used (see section 10 "Testing and rec- tification"). Tab. 1: Multi-LED continuous illumination Rittal PSM MID measuring module for CMC III... -
Page 12: Description Of Operation
"Return" key to confirm the selection (fig. 4, the following parameters item 5). All setting values of the PSM MID measuring module are then reset to the factory default and the start screen appears. Rittal PSM MID measuring module for CMC III... -
Page 13: Settings For The Two Infeeds
The value is changed in 1 V steps. Press the "Return" key to confirm your input. Phase 3 Information The symbols change again to ">*" before or "*<" af- Circuit 2 ter the entry. Rittal PSM MID measuring module for CMC III... -
Page 14: Messages On The Main Display
(fig. 6) and all actual measured values for infeed 1 can changes are described in detail. There are also dis- be viewed at a glance. play values used only for information purposes. Rittal PSM MID measuring module for CMC III... - Page 15 The following descriptions assume that you have se- SetPtLow- Lower limit of the current value for which lected the tree representation. Alarm an alarm message is issued. Rittal PSM MID measuring module for CMC III...
- Page 16 The following parameters are also displayed for phase L1 in the associated sublevels: Tab. 11: Settings in the "Voltage" level Rittal PSM MID measuring module for CMC III...
-
Page 17: Circuit 2
L2 and L3 in the appropriate levels as for phase L1. 7.5.3 Circuit 2 Settings for infeed 2 are performed at the "Circuit 2" level. The representations match fully those for infeed 1 (see section 7.5.2 "Circuit 1"). Rittal PSM MID measuring module for CMC III... -
Page 18: Inspection And Maintenance
After expiration of the calibration end date printed on the measuring module, the unit must be recalibrated if it is still to be deployed for billing purposes. If necessary, contact Rittal for a recalibration of the unit. 8.2.5 Test procedure To test the unit, an adaptor kit can be obtained from Rittal (see section 13 "Customer service addresses"). -
Page 19: Storage And Disposal
9 Storage and disposal Storage and disposal Storage If the device is not used for a long period, Rittal rec- ommends that it is disconnected from the mains pow- er supply and protected from dampness and dust. Disposal Because the PSM MID measuring module consists primarily of the "housing"... -
Page 20: Testing And Rectification
Change the "Disp. Circuit" setting in the configura- tion menu to "Source 1" (see section 7.4.1 "Settings using the configuration menu"). Then change the "Disp. Circuit" setting to the appro- priate entry for the actual connection configuration. Rittal PSM MID measuring module for CMC III... -
Page 21: Technical Specifications
Freely settable limit values for warning/alarm Main display, centre OLED monochrome (5 lines) Metrology LEDs 10,000 pulses = 1 kWh Interfaces 2 x RJ 45, CAN bus MTBF (at 40 °C) 200,000 hours Rittal PSM MID measuring module for CMC III... - Page 22 IP 51 according to IEC 60 529 Storage temperature –25 °C to +55 °C Ambient operating temperature –25 °C to +55 °C Operating humidity range 20% to 90% relative humidity, non-condensing Tab. 17: Technical specifications Rittal PSM MID measuring module for CMC III...
-
Page 23: Accessories
Connection cable set for PSM busbars (with Wago-X-Com connectors) 7859.316 (2 x required when both infeeds are used) Tab. 18: Accessories PSM-MID M16 (DK 7859.312) Designation Model No. DK Connection cable set, 1 x input 3 m / 1 x output 1 m CEE (IEC 60 309) 7859.335... -
Page 24: Customer Service Addresses
13 Customer service addresses Customer service addresses For technical questions, please contact: Tel.: +49 (0)2772 / 505-9052 E-mail: info@rittal.de Homepage: www.rittal.com For complaints or service requests, please contact: Tel.: +49 (0)2772 / 505-1855 E-mail: service@rittal.de Rittal PSM MID measuring module for CMC III... - Page 26 Enclosures Power Distribution Climate Control IT Infrastructure Software & Services RITTAL GmbH & Co. KG Postfach 1662 · D-35726 Herborn Phone +49(0)2772 505-0 · Fax +49(0)2772 505-2319 E-mail: info@rittal.de · www.rittal.com...
Need help?
Do you have a question about the DK 7859.312 and is the answer not in the manual?
Questions and answers