Related Manuals for Rittal DK 7859.212
Summary of Contents for Rittal DK 7859.212
- Page 1 PSM (Power System Module / PCU) DK 7859.212 DK 7859.222 DK 7859.232 DK 7859.215 DK 7859.225 DK 7859.235 Assembly, installation and operation A34113 12 IT 74...
- Page 2 Microsoft Windows is a registered trademark of Microsoft Corporation. Acrobat Reader is a registered trademark of Adobe Systems Incorporated.
-
Page 3: Table Of Contents
Notes on documentation 1 7.5 Defining the PSM module on the CMC-TC PU II Contents (CMC-TC operation) ........12 Notes on documentation....4 Browser monitoring (as of SW 2.45) 1.1 Other applicable documents ......4 1.2 Storing the documents ........4 8.1.1 Login ..........13 1.3 Symbols used............ -
Page 4: Notes On Documentation
PSM busbar. Other tasks associated with the PSM, such as the assembly and in- Rittal can accept no liability for damage and operat- stallation of system components with tested ing disturbances resulting from non-compliance with standard connectors, and the operation and these instructions. -
Page 5: Device Description 3
7-segment display on the front side. When 3.4 Scope of delivery this is connected to the Rittal CMC-TC PU II or the external power pack (DK 7201.210), the currently The unit is supplied in a packaging unit in a fully consumed power of the complete module will be assembled state. -
Page 6: Accessories
3 Device description IEC connector plug connec- 3.5 Accessories tion cable Country vari- 7200.214 3.5.1 Required accessories (CMC-TC) USA/CDN, The operation of the PSM module requires a fully- UL-approval FT1/VW1 installed PSM busbar provided with power. You require the following accessories to administer IEC 320 connector and monitor the PSM module from the network. -
Page 7: Pack)
3.6 Proper use CMC-TC Length 0.5 m 7320.470 RJ45 Length 2 m 7320.472 The Rittal PSM module serves as power supply or connec- tion power distribution system. It can be connected to Length 5 m 7320.475 cable the Rittal CMC-TC monitoring system. -
Page 8: Assembly
4 Assembly Attach the Velcro tapes to the CMC-TC PU housing Assembly and position the CMC-TC PU at the required at- 4.1 Notes for the assembly of the CMC- tachment location. TC PU Install the CMC-TC PU in an enclosure or in a suit- able housing system so that it is also protected from external effects. -
Page 9: Assembly Of The Pcu In The 19" Level
5.1 Safety instructions and other notes level The Rittal PSM module may only be oper- The Rittal PCU (7859.225 / 7859.235) has the same ated with PE conductor connection. The PE construction form as the PSM modules other than it... -
Page 10: Connecting Further Psm Modules
6 Operation with power pack 6.1 Connecting further PSM modules (power pack operation) 6.2.3 Limit values of the multicolour LED A maximum of four modules may be connected in display series. Snap the module into the PSM busbar as described previously. Insert the RJ45 cable into the If the PSM module or the PCU is operated with po- free socket of the first module and the other end in wer pack, the limit values for which the LEDs of the... -
Page 11: Resetting The Psm Module To The Factory Setting (Power Pack Operation)
Operation with CMC-TC 7 automatically so that the values can be read opti- Operation with CMC-TC mally. If the PSM busbar with the PSM modules is moun- ted in the raised floor, the position sensor does not know how the display should be. It is the same for the horizontal installation of the PCU (7200.001) in the 19"... -
Page 12: Configuring The Display (Cmc-Tc Operation)
7 Operation with CMC-TC Press the button briefly until the address "1" ap- Wait a few seconds until the display changes in the pears. status display (actual current value). Press the button for three seconds to save the ad- 7.4 Resetting the PSM module to the dress. -
Page 13: Browser Monitoring (As Of Sw 2.45) 8
Browser monitoring (as of SW 2.45) 8 8.1.3 General overview (status window) Browser monitoring (as of SW 2.45) Open your browser in the usual manner. Enter in the address line the IP address of the CMC-TC Proc- essing Unit. The login window will appear. 8.1.1 Login Fig. -
Page 14: Individual Current Measurement
8 Browser monitoring (as of SW 2.45) 8.2.1 Setup settings Ten sensor values, ten output values and ten meas- Individual current measurement ured values can be configured for each connected module. The PSM/PCU bars have their own current meas- Ten tabs can be selected for each module, where urement for each switch output. - Page 15 Browser monitoring (as of SW 2.45) 8 The 'Advanced' button can be used to switch to a second settings page (see Fig. 21). This page can be used to set the 'High', 'Warning' and 'Low' set- points for each of the eight (six) relay outputs. Settings for the alarm type and the alarm recipients can also be made.
-
Page 16: Current Measurement Settings
8 Browser monitoring (as of SW 2.45) 8.2.3 Current measurement settings Tab 9 shows the total current ('Current PSM') and the overall status of each module (see Fig. 22). This page can be used to set the 'High', 'Warning' and 'Low' setpoints for the complete module. Settings for the alarm recipient and the alarm type can also be made here. -
Page 17: Configuring The Active Psm
Browser monitoring (as of SW 2.45) 8 8.2.6 Configuring the active PSM Alarm Beeper Beeper should sound (enable) or not sound (disable) for warn- ing/alarm. Navigation Alarm Reset Warning/alarm should be ac- Main menu – Status – Click 1st current knowledged automatically (Auto) or must be acknowl- Parameter... -
Page 18: Maintenance And Cleaning
9 Maintenance and cleaning entered previously for Setup – The Rittal PSM module is a maintenance-free sys- eMail (SMTP); each address is tem. The housing does not need opening for instal- separated with the "&" charac- lation or operation. -
Page 19: Storage And Disposal 10
10-16 A for 230 VAC, Further information and the current operating in- 10-15 A for 110 VAC, structions and updates of the Rittal CMC-TC can be depending on the country downloaded from the Security section of the Rima- variant, refer to the rating trix5 homepage. -
Page 20: Technical Glossary
13 Technical glossary Designation PCU module (7859.225) CMC-TC CMC-TC (Computer Multi Control - Top Concept) is Designation PCU module (7859.235) a Rittal product used to monitor network enclosure Enclosure components. Internet Browser Housing type Aluminium, anodised, plastic caps An internet browser can be used to display html... -
Page 21: Notes 14
Notes 14 14 Notes Active 8-way PSM modules...
Need help?
Do you have a question about the DK 7859.212 and is the answer not in the manual?
Questions and answers