Table of Contents
Advertisement
How to Use Your Pedalino
These two pages show the current settings for the thresholds of the respective
sets. The thresholds are symbolised here by the number of LEDs [7] that will
light up when the threshold is reached (
first example above, the current 'soft' set has the global LEVEL 2 threshold set
at 46, while the LEVEL 3 threshold is set at 55.
To adjust the threshold(s), press the SET key [11] when on page 2 or 3 of
•
the menu. The cursor will appear under the value of the threshold for
LEVEL 2.
•
Use the + key [8] and the – key [9] to increase or decrease the value of
the global threshold and the SET key [11] to switch between the global
threshold for LEVEL 2 and LEVEL 3.
The thresholds for Level 1 have been set at an optimal default value
by VR and cannot be modified.
By decreasing the value of a threshold (e.g., from 46 to 41), less force now
needs to be applied to each of Pedalino's four pads in order to reach the
corresponding level. Likewise, increasing the threshold (e.g., from 55 to 59)
will increase the amount of force required to reach that level.
Soft level
While in the pad preference menu it is possible to try out the thresh-
8
olds AS you are customising them (either the predefined thresholds
or those you are adjusting). Simply press pads [13], [14], [15] or
[16], and look at the force-feedback LEDs [7] to check how much
force you need to apply to activate that particular level.
•
When you are done with adjusting the global thresholds, press the EXIT
key [12] TWICE to return to browse mode or to favourite mode.
Rev. 2.0 - EN EU - fw 4.22
for LEVEL 2;
ÜÜ
ÜÜÜ
s
2
/3
ÜÜ 41
:
ÜÜ 59
: Ü
-
8.8.5 Customising individual pads' thresholds
for LEVEL 3). In the
The global thresholds described above apply to all four pads [13] to [16] of
your Pedalino. However you also have the option of fine-adjusting the thresh-
olds for LEVEL 2 and/or LEVEL 3 of each individual pad for an even higher
level of personal customisation. This can be done for both the 'soft' or the
'hard' sets, independently.
•
To fine tune the thresholds of the 'soft' set, go to page 2 of 3 of the 'Pad
preference' menu, as shown in the
ites switch [4]. The following screen will appear:
•
In this screen, adjust the thresholds for LEVEL 2 (
each pad. The numerical values on the bottom line of the display indi-
cate an individual offset applied to each one of the four pads. The order,
from left to right, of the four offsets on the bottom line corresponds to the
order of the four pads of your Pedalino (BYPASS/MUTE [13],
[15], and
Negative offset values reduce the threshold for that particular pad, with
respect to the global threshold value for the selected set and level. Positive
offset values have the effect of increasing the threshold for that particular
pad.
In the example below, we are fine tuning the thresholds for LEVEL 2 of the
'soft' set. The offsets shown below are applied:
26
8.8.2. Now press the Favour-
section
Ad j u
st
s
oft
+
4
-
3
0
-
+
pad [16], respectively).
Ad j u
st
s
oft
ÜÜ
+
4
-
3
0
-
13
14
15
ÜÜ
1 +
) of the 'soft' set of
ÜÜ
−
[14], Load
1 +
16
Advertisement
Table of Contents
