Page 1
Service Manual Lighting Consoles Avab jaguar/Pronto! CPU Peak 603VL dual video power supply 100W All rights reserved. No part of this manual may be reproduced or copied in any form without the written approval of transtechnik Lichtsysteme GmbH & Co. KG.
Avab NEKYEV4VSRXS Security Security Symbols This manual uses the symbols depicted below for Danger, Caution and Note: Danger This symbol indicates situations where failure to follow the instructions carefully can result in danger to life, injury or accidents. Caution This symbol indicates situations where failure to follow the instructions carefully can cause damage to your equipment.
Avab Jaguar Common Rules Common Rules Repairing jaguar should be limited to changing assemblies. Faulty assemblies should be returned to transtechnik for repair. Changing assemblies is simple. Keep in mind following rules, to preserve full operation and reliability of your console.
Avab Jaguar Common Rules Tools and Supply Material To repair jaguar you do not need any special tools. Equipped with following simple tools you should be able to change all assemblies without any problem. • Screw driver of several sizes (standard or Phillips) Tools •...
Avab Jaguar Common Rules Handling Printed Circuit Boards Some printed circuit boards are equipped with CMOS-type parts. They are sensitive to overvoltage. Uncontrolled touch of PCBs can destroy those parts. Consider following precautions, to avoid accidental damage: 1. Touch PCBs or parts only for repair purpose.
Avab Jaguar Bottom Part Bottom Part Overview Assemblies Figure 1: View bottom part of jaguar. Mains supply filter Floppy connection PCBs CPU assembly CPU-card Power supply Dongle Dual video Voltage control IO2 -card harddisk Accumulator Pronto_Peak603VL_eng – 7 – Version 1.2, Nov. 2003...
Avab Jaguar Bottom Part Power Supply Power supply is divided into 2 parts: • Power supply unit generates 15V DC from mains supply. • Voltage control TT-1778 generates additionally +5V, +/-12V and +/-15V. On power fail, it switches to accumulator power controlled by a signal from the IO2 card.
Avab Jaguar Bottom Part Adjust Output Voltages For proper operation of the console the output voltages have to be adjusted carefully. Procedure Power supply unit has to be installed and connected properly All assemblies must be properly in place and fixed, no loose parts should be visible...
Avab Jaguar Bottom Part Mains Filter Figure 4: Figure 5: Right rearward corner from inside. Power supply, Right rearward corner from outside. Fuses are located mains filter and mains switch are visible. between switch and mains connector. Remove Unplug mains supply.
Avab Jaguar Bottom Part Change Mains Fuses Fuse can be changed without opening console There are two fuses, one for power and one for ground. Figure 6: Mains switch with fuses removed. Procedure Unplug mains supply On rear side, open cover below mains switch Change fuses, Type T 3,15A Never short fuses or use fuses with higher values.
Avab Jaguar Bottom Part Remove Take care on electric charges For handling of CPU board please refer to instructions on page 6 To avoid mix up on installation care for clear labeling of cables connected to the CPU Unplug all cables, if necessary, unfasten screws...
Avab Jaguar Bottom Part IO2-Card TT-1826 Figure 9: View IO2-card, dipswitches and jumpers are tagged Remove Remove CPU card, see above Remove fastening screw from attachment device on left side. Unplug all connections to TT-1826 Pull out IO2-card to the right Install All jumpers must be plugged in, dipswitches must be in position “ON”...
Avab Jaguar Bottom Part VGA Cards Figure 10: View CPU and VGA cards Remove Take care on electric charges For handling of CPU board please refer to instructions on page Detach and unplug monitor cable Remove fastening screw from attachment device on left side.
Avab Jaguar Bottom Part Back Panel Figure 11: Figure 12: View upper PCB (TT-1966) on back panel. View lower PCB (TT_1965) on back panel, Figure 13: PCBs on back panel Remove Unplug all cables Unfasten 10 screws M3 from back panel and remove PCBs...
Avab Jaguar Bottom Part Hard Disk Figure 14: hard disk Remove Unplug flat cable (notice red marking) and power lines Unfasten 4 screws attaching the hard disk unit to the assembly and take it out. Install Attach hard disk unit by 4 screws to assembly Plug in flat cable (notice red marking on cable) and power lines.
Avab Jaguar Bottom Part Floppy Disk Drive Figure 15: View assembly floppy drive Remove Unplug flat cable (note red marking) and power cable from drive Remove assembly by unfastening 2 screws on rear plane Unfasten 4 screws attaching the hard disk unit to the assembly and take it out.
Avab Jaguar Bottom Part Dongle Figure 16: View dongle and mounting adapter Dongle Knob Dongle Housing If you have to exchange the dongle you additionally have to change the dongle code. If you do not provide the appropriate dongle code jaguar will only run in demo mode. Some skill running DOS commands and running the DOS editor are helpful.
Avab jaguar/Pronto! Front panel Front panel Assemblies Front Panel Rate Wheel Level Wheel Parameter Wheels LED Display BO-switch Front Panel CPU LCD Display Pronto_Peak603VL_eng – 20 – Version 1.2, Nov. 2003...
Avab jaguar/Pronto! Front panel Wheels Figure 17: Wheels bottom view Encoder PCB Level wheel Rate wheel Remove Unplug connectors Remove PCB TT-1784 by unfastening nut M3 from retaining bracket After removing 3 nuts M3 and thread pin remove wheel According to this procedure, all wheels can be removed Pronto_Peak603VL_eng –...
Page 22
Avab jaguar/Pronto! Front panel Retainig brackets Adjusting screw Figure 18: Figure 19: Top view wheels, sensor PCB removed Wheel side view, optical encoder disk Install Mount retaining brackets of wheel assembly to thread pins and fasten nuts on one side Adjust brackets on second side.
Avab jaguar/Pronto! Front panel Align Photo Sensor Figure 20: Detailed view of sensor attachment Attachment bracket Movement of the wheel is tapped by a photo sensor from an encoding disk attached to the wheel. For proper operation the photo sensor mounted onto the encoder PCB must have a distance below 1 mm from the...
Avab jaguar/Pronto! Front panel Front Panel Controller TT-1781 Figure 21: Bottom view front panel, location of front panel controller PCB EPROM front panel control software Remove Before you start, label all cables Unplug flat wire cables (note red marking) and all the other cables...
Avab jaguar/Pronto! Front panel Update Software Front Panel Controller for jaguar Front panel software is recorded in a Flash-EPROM. Refer to figure 21 on page 30. Additionally it includes boot software. Starting with boot version 1.01 and front panel software release 1.07 the software can be loaded from hard disk.
Avab jaguar/Pronto! Front panel Update Software Front Panel Controller for Pronto Front panel software is recorded in a Flash-EPROM. Refer to figure 21 on page 30. Additionally it includes boot software. Starting with boot version 1.01 and front panel software release 1.07 the software can be loaded from hard disk.
Avab jaguar/Pronto! Front panel LCD Display Figure 22: Location of the LCD display below the the front panel controller LCD display Remove The LCD display is accessible after front panel controller is removed, refer to page 24) Unplug flat wire cable, note red marking...
Avab jaguar/Pronto! Front panel LED Displays Figure 23: Detailed view of a LED display Brackets Remove Procedure is identical for all 3 displays Unplug flat wire cable , notice red marking Unfasten both nuts M3 and remove brackets Install Take care on the orientation of the display Insert display.
Avab jaguar/Pronto! Front panel Blackout Switch Figure 24: Bottom view blackout switch BO switch Remove On top side, remove protective cap from BO switch Unsolder wires Unfasten union nut and remove switch Install Insert switch and fasten it by union nut...
Avab Jaguar Change Configuration Change Configuration for jaguar To change configuration of jaguar (number of channels, attributes, outputs or unlocking of software options) you need a new dongle code. Contact your dealer or transtechik. The new code has to be inserted into jaguar.
Avab Jaguar Change Configuration jaguar Startup File On power on jaguar comes up with MSDOS. Last step in this procedure is an automatic call to the startup file V.BAT from AUTOEXEC.BAT. The batch file starts drivers and the jaguar software. Refer to the manual about options.
Avab Jaguar Change Configuration Contact transtechnik If you contact transtechnik following data should be available: • Serial number of your jaguar You can find it on the rear panel on a sticker. Example: 1033693 B • Software version you are running on your jaguar Menu About Example: 2.10.18...
Avab Jaguar Change Configuration Change Configuration for Pronto Pronto configuration regarding number of channels and outputs is noted in file PRONTO.CFG in directory C:>\PRONTO. The built in hardware dongle limits those numbers according to the ordered configuration. To upgrade number of channels or outputs your Pronto is working with you have to contact your dealer or transtechnik to order a new dongle code.
Avab Jaguar Change Configuration Edit PRONTO.CFG Shutdown Pronto: Alt-X on the keyboard or File menu – Shutdown Monitor displays: C:>\PRONTO Edit PRONTO.CFG using MSDOS command EDIT: EDIT PRONTO:CFG See example from figure 27 Update dongle code: Insert new line in line marked SystemConfig...
Avab Jaguar Change Configuration Contact transtechnik If you contact transtechnik following data should be available: • Serial number of your Pronto You can find it on the rear panel on a sticker. Example: 1113723B • Software version you are running with your Pronto From Pronto! menu select “About Pronto!”.
Avab Jaguar List of Assemblies List of Assemblies ID-Nr. = order number Assembly ID-Nr. Position Page Accumulator 24146 Bottom, right front Accumulator fuse 6,3A 08671 Bottom, right front Power supply unit 30433 Bottom, right rear Voltage control 21905 Bottom, right rear...