Advertisement
Press and release SW1 until a channel ID number corresponding to a BIM-22-2 is shown. Press and hold
SW1. The message display will show LABEL.
Press and hold SW1. The message display will show LOW WARN SET. Release SW1. The display will
highlight the Low Warning threshold of the BIM channel you have selected. If you want to change the Low
Warning threshold at this time, press and release SW1 until the value desired is shown.
To exit Low Warning setup, press and hold SW1. The message display shows HIGH WARN SET. Release
SW1. The display will highlight the High Warning threshold of the BIM channel you have selected. If you want
to change the High Warning threshold at this time, press and release SW1 until the value desired is shown.
The Low and High Warning thresholds of remaining channels (tires) are changed following the steps above.
To go to the Location procedure, Press and hold SW1. The message display will show TIRE LOCATE SKIP.
Press and release SW1 so that BEGIN is displayed. Press and hold SW1. If the message FILL LOW TIRES is
displayed, it is possible sensor(s) need to be woken up. Sensors wake up with a change in pressure of more
than 2 PSI. Another possibility is that one or more tires do not have at least 20 PSI of pressure. Inflate all tires
so that all of them have at least 20 PSI.
Once all sensors are awake and all tires have at least 20 PSI, the display will show DEFLATE LEFT FRONT.
At this time, deflate the tire located at the Left Front (driver side, front axle) of the vehicle. When the control
box has seen enough of a pressure decrease to determine the sensor's location, display shows DEFLATE
RIGHT FRONT. Deflate the tire located at the Right Front (passenger side, front axle).
When the control box has determined which sensor is at this location display will show DEFLATE LEFT REAR.
At this time, deflate the tire located at the Left Rear (driver side, rear axle).
When the control box has determined which sensor is at this location the system will automatically determine
the location of the Right Rear tire (passenger side, rear axle) and display FILL LOW TIRES. This is a reminder
to fill all tires to their recommended levels before driving on them.
Press and release SW1. The display will show DONE. Press and release SW1 to exit the LOCATE procedure.
Press and release SW1 until BIM SETUP DONE is displayed. Press and hold SW1 to exit BIM setup.
Locating sensors and setting warning levels on a VFD3 or VFD3X system:
Press and hold SW1 while turning the key on. The speed display will show SET and the message display will
show SETUP. Release SW1. Press and release SW1 until BIM shows in the message display.
Press and hold SW1. The message display will show SCAN followed by the number of BIM channels detected.
Release SW1. If 0 is shown, check all connections and press and hold SW1 with SCAN shown to retry reading
the modules. Otherwise, if any other number is shown, press and release SW1 until SETUP is shown.
Press and hold SW1 until the speed display shows " – " and the message display shows SETUP.
Release SW1. The message display will show the label assigned to the first channel found and the speed
display will show "C" followed by the channel ID number. Press and release SW1 until the channel for a Tire
Pressure BIM is shown. (For example, the message display will display LF TIRE).
Press and hold SW1 until "-" shows in the speed display and WARN shows in the message display.
Release SW1. The message display shows "L" and the current Low Warning setting. If you want to change the
Low Warning threshold at this time, press and release SW1 until the value desired is shown.
Press and hold SW1. The message display shows "H" followed by the current High Warning value. If you want
to change the High Warning threshold at this time, press and release SW1 until the desired value is shown.
If you want to change the Low or High thresholds of other channels (tires), repeat the steps above.
Press and hold SW1. The speed display will show LOC and the message will display SKIP. Press and release
SW1 until the message display shows BEGIN. Press and hold SW1. If the message FILL LO X TIRES, where
X is the number of tires remaining to be filled (Example: FILL LO 2 TIRES) is displayed, it is possible sensor(s)
need to be woken up. Sensors wake up with a change in pressure of more than 2 PSI. Another possibility is
that one or more tires do not have at least 20 PSI in them. Inflate all tires to at least 20 PSI.
Once all sensors are awake and all tires have at least 20 PSI, the message display will show DEFLATE LF
TIRE. At this time, deflate the tire located at the Left Front (driver side, front axle) of the vehicle.
When the system has detected enough of a pressure decrease to determine the sensor's location, the
message display will show DEFLATE RF TIRE. At this time, deflate the tire located at the Right Front
(passenger side, front axle).
When the system has determined which sensor is at this location, the message display will show DEFLATE
LR TIRE. At this time, deflate the tire located at the Left Rear (driver side, rear axle).
MAN#650598
Advertisement
