Advertisement
Quick Links
OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS
COLOR
•
BLACK • UniDrums • UniRollers • UniParts • UniCoatings
Absolute
Absolute
OKIDATA B6300 PRINTER
REMOVING THE CHIP
1. Using a small screwdriver, push in one of
the tabs located beneath the base to
release the chip that is held in place.
www.
uninet
imaging.com
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • techsupport@uninetimaging.com
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
AbsoluteCOLOR
®
2. The chip can now be lifted from the top
or pushed out through the tab holes
beneath the chip base.
USA
EUROPE
Ph:
+310-280-9620
+34-93-757-1335
Fx:
+310-838-7294
+34-93-741-4166
• AbsoluteBLACK
®
• UniDrums • UniRollers • UniParts • UniCoatings
TONER CARTRIDGE
WITH OEM CHIP SHOWN
3. Chip removed with tab holes shown. It
will be replaced later with a new
Smartchip.
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
ARGENTINA
+55-11-4822-3033
+54-11-4574-3706
+55-11-4822-3353
+54-11-4574-3706
Advertisement
Related Manuals for OKIDATA B6300
Summary of Contents for OKIDATA B6300
- Page 1 AbsoluteCOLOR ® • AbsoluteBLACK ® • UniDrums • UniRollers • UniParts • UniCoatings OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS COLOR • BLACK • UniDrums • UniRollers • UniParts • UniCoatings Absolute Absolute TONER CARTRIDGE WITH OEM CHIP SHOWN OKIDATA B6300 PRINTER REMOVING THE CHIP 2.
- Page 2 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS SPRING 4. Remove the shutter-door arm from the 5. Using a hook tool, remove the shutter- 6. Remove the shutter-door and set it slot on the gear-side of the toner cartridge door arm on the gearless side. Remember aside.
- Page 3 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS 13. Use a hook tool to release the spring 14. Lift evenly to separate the drum unit 15. Drum unit removed. from the gear-less side. from the cartridge. 16. You are now ready to disassemble the 17.
- Page 4 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS 22. Carefully remove the drum. 23. You are now ready to remove the PCR. 24. Remove the PCR by un-clipping it from the white and black holders. 25. Remove the wiper blade by unscrewing the two gold-colored screws at each end that 26.
- Page 5 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS 30. Reinstall the wiper blade back into position with the two gold-colored screws as shown. 31. Reinsert the PCR into the clips by using slight force. 32. Reinsert the OPC gear side first.
- Page 6 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS 37. The end-cap should then slide out. 38. Remove all gears from the cartridge as shown in the following photos. These gears are designed to fit one way, so reinstalling won’t become too difficult.
- Page 7 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS 43. Unscrew the two gold-colored screws that hold the the Doctor 44. Doctor Blade removed. Blade in place as shown. 45. Using a pair of needle-nose pliers, remove the two toner fill plugs located on the gear 47.
- Page 8 UNINET IMAGING INC. • OKIDATA® B6300 REMANUFACTURING INSTRUCTIONS 48. Toner hopper removed. Note the two 49. These foam seals surround holes 50. Clean the hopper and toner cartridge foam seals located at the bottom of the where toner passes through to the develop- using compressed air or a vacuum.