Download
Share
Print this page
Nordson Rhino SD3 Instruction Sheet
  1. Manuals
  2. Brands
  3. Nordson Manuals
  4. Accessories
  5. Rhino SD3
  6. Instruction sheet

Nordson Rhino SD3 Instruction Sheet

Electric container level sensors
Hide thumbs Also See for Rhino SD3:

Advertisement

Quick Links

Download this manual
Description
55-Gallon Frame
Shown for Reference Only
Figure 1
Container Level Sensors
E 2019 Nordson Corporation
See Figure 1. The Rhino
magnetic sensors to monitor the distance between the bottom of the follower plate
and the base surface of the unloader frame.
The module contains two to four sensors depending on system configuration:
S
Drum Empty (4)
S
Drum Low (if equipped) (3)
S
Follower-in-Drum (2)
S
Ram Top of Stroke (if equipped) (1)
When a magnet on the frame piston moves in front of the applicable sensor, the
sensor sends a signal to the controller.
r
Rhino
SD3/XD3 Electric
Container Level Sensors
r
SD3/XD3 electric container level sensor module uses
1
2
3
4
Instruction Sheet
P/N 1615748-01
Part 1615748-01
10018538

Advertisement

loading

Related Manuals for Nordson Rhino SD3

Summary of Contents for Nordson Rhino SD3

  • Page 1 When a magnet on the frame piston moves in front of the applicable sensor, the sensor sends a signal to the controller. 55-Gallon Frame Shown for Reference Only 10018538 Figure 1 Container Level Sensors Part 1615748-01 E 2019 Nordson Corporation...
  • Page 2 Drum Low (if equipped), Follower-in-Drum, and Ram Top of Stroke (if equipped), signal levels. NOTE: Read and understand these procedures before installation. If necessary, contact a local Nordson representative for assistance. See Figure 2. 1. Turn the power off to the unloader.
  • Page 3 Rhino SD3/XD3 Electric Container Level Sensors 55-Gallon Frame Shown for Reference Only 10018538 Figure 2 Installing/Moving Magnetic Sensors Part 1615748-01 E 2019 Nordson Corporation...
  • Page 4 2. Repeat step 1 for the remaining magnetic sensors if necessary. 3. Use the control valve to and lower the follower plate to test the Follower-in-Drum, Low, and Empty Level signals. 4. Adjust as necessary. Part 1615748-01 E 2019 Nordson Corporation...
  • Page 5 5. Repeat steps 1-3 for the remaining magnetic sensors if necessary. 6. Use the control valve to lower the follower plate to test the Follower-in-Drum, Low, and Empty Level signals. 7. Adjust as necessary. Part 1615748-01 E 2019 Nordson Corporation...
  • Page 6 NOTE: Spacer on top of base-plate rails. NOTE: Spacer on top of base-plate rails. Follower-in-Drum Height: NOTE: This setting MUST be adjusted in the field to the customer specific container being used. 10017433 Figure 3 Factory Setting for 55-Gallon Part 1615748-01 E 2019 Nordson Corporation...
  • Page 7 10017433 Figure 4 Factory Setting for 5-Gallon MINI-TOTE FOLLOWER PLATE Empty Setting Height: 2.375 in. NOTE: From bottom of sensor to top of cylinder base. 10017433 Figure 5 Factory Setting for Mini-Tote Part 1615748-01 E 2019 Nordson Corporation...
  • Page 8 Repair consists of replacing the magnetic sensors and setting the Drum Empty, Drum Low, Follower-in-Drum, and Ram Top of Stroke signal levels. NOTE: Read and understand these procedures before performing repairs. If necessary, contact a local Nordson representative for assistance. Replace a Magnetic Sensor See Figure 6.
  • Page 9 Rhino SD3/XD3 Electric Container Level Sensors 55-Gallon Frame Shown for Reference Only 10018538/10018991 Figure 6 Replacing a Magnetic Sensor Part 1615748-01 E 2019 Nordson Corporation...
  • Page 10 Rhino SD3/XD3 Electric Container Level Sensors Parts To order parts, call the Nordson Industrial Coating Systems Customer Support Center at (800) 433−9319 or contact your local Nordson representative. Container Level Sensors See Figure 7 and refer to the following parts lists.
  • Page 11 — S SENSOR, assembly, rhino, cylinder, SD3/XD3, 1617235 80/100 mm 1617238 S S SENSOR, cylinder, Rhino SD3/XD3 1617239 S S MOUNT, sensor, cylinder, 80-100 mm S S NUT, hex, jam, M3 x 0.5 x 8, steel, zinc, per ISO −−−−−−...
  • Page 12 10018521 Rhino SD3/XD3 Level Sensor Schematics Issued 06/19 Original copyright date 2019. Rhino, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation. All other trademarks are the property of their respective owners. Part 1615748-01 E 2019 Nordson Corporation...
  • Page 13 EXPANSION BLOCK MASTER BLOCK INPUTS INPUTS INPUTS OUTPUTS PIN 1 PIN 1 PIN 1 PIN 1 INPUT X1-B PIN 2 X1-A X5-A PIN 2 INPUT X5-B NOT USED PIN 2 X1-A X5-A PIN 2 OUTPUT X5-B RAM DOWN SELECTOR SWITCH FOLLOWER IN DRUM LIGHT TOWER PIN 3...
  • Page 14 EXPANSION BLOCK MASTER BLOCK INPUTS INPUTS INPUTS OUTPUTS PIN 1 PIN 1 PIN 1 PIN 1 INPUT X1-B PIN 2 X1-A X5-A PIN 2 INPUT X5-B NOT USED PIN 2 X1-A X5-A PIN 2 OUTPUT X5-B RAM DOWN SELECTOR SWITCH FOLLOWER IN DRUM LIGHT TOWER PIN 3...
  • Page 15 EXPANSION BLOCK MASTER BLOCK INPUTS INPUTS INPUTS OUTPUTS PIN 1 PIN 1 PIN 1 PIN 1 X1-A X5-A X1-A X5-A INPUT X1-B PIN 2 PIN 2 INPUT X5-B NOT USED PIN 2 PIN 2 OUTPUT X5-B RAM DOWN SELECTOR SWITCH LIGHT TOWER PIN 3 X1-B X5-B...
  • Page 16 EXPANSION BLOCK MASTER BLOCK INPUTS INPUTS INPUTS OUTPUTS PIN 1 PIN 1 PIN 1 PIN 1 INPUT X1-B PIN 2 X1-A X5-A PIN 2 INPUT X5-B NOT USED PIN 2 X1-A X5-A PIN 2 OUTPUT X5-B RAM DOWN SELECTOR SWITCH LIGHT TOWER PIN 3 X1-B X5-B...

This manual is also suitable for:

Rhino xd3