Explanation Of Indicators - Sony UP-DR80MD Instructions For Use Manual

Explanation of Indicators

The meanings of the indicators on the printer when they
are on or flashing are described below.
Indicator Status
1 On/
On
standby
Flashing
(green)
TRAY On
LOCK
(orange)
RIBBON/ On
1)
PAPER
(orange)
Flashing
1)
ALARM On
(orange)
RIBBON/ On
PAPER,
1)
ALARM
28
Explanation of Indicators
Possible causes and remedies
The printer is turned on.
The printer is entering the standby
state.
• The media tray cannot be pulled
out.
tDo not pull out the media tray.
One of the following causes.
• A paper roll has not been loaded.
t Load a paper roll (page 17).
• An ink ribbon has not been loaded.
tLoad an ink ribbon (page 16).
• The ink ribbon has been used up.
tLoad a new ink ribbon and paper
roll (page 19).
• A ribbon error has occurred.
tCheck that an ink ribbon has
been loaded properly.
• The paper roll is the wrong size.
tSet the paper holder selector
properly (page 16).
One of the following causes.
• Thermal head or roller cleaning is in
progress.
• The printer is waiting to begin roller
cleaning.
tPress the STOP button to begin.
• The cleaning ribbon is loaded.
tRemove the cleaning ribbon.
One of the following causes.
• The media tray is not closed.
tClose the media tray properly.
• A paper jam has occurred in the
printer.
tRemove the jammed paper
(page 29).
• The paper outlet is full of printouts.
tRemove the printouts that are
blocking the paper outlet.
One of the following causes.
• The paper roll has run out.
tLoad a new ink ribbon and paper
roll (page 19).
• A paper feed error has occurred.
tCheck the ink ribbon and paper
roll.
• A paper eject error has occurred.
tCheck the ink ribbon and paper
roll.
Indicator Status Possible causes and remedies
2)
Flashing One of the following causes.
• A ribbon error occurred while
cleaning was in progress.
tCheck that the cleaning ribbon
• A paper jam occurred inside the
printer while cleaning was in
progress.
tRemove the jammed paper
• The paper roll ran out while
cleaning was in progress.
tLoad a new paper roll.
• A feed error occurred while
cleaning was in progress.
tCheck the cleaning ribbon and
• An eject error occurred while
cleaning was in progress.
tCheck the cleaning ribbon and
PRINT On Printing is in progress.
(green)
Flashing Image data is being received.
Flashing The printer is waiting until the thermal
slowly head reaches a temperature at which
printing is possible. Once that
temperature is reached, the PRINT
indicator will light.
All of TRAY On • The printer is initializing.
tAfter pressing the 1 On/standby
LOCK,
RIBBON/
PAPER,
ALARM,
and PRINT
• The media tray was opened during
printing.
tPress the 1 On/standby switch
• A serious failure has occurred.
tPress the 1 On/standby switch
1)
During continuous printing, the PRINT indicator lights at the
same time if there are still images remaining.
2)
Only the RIBBON/PAPER indicator flashes. The ALARM
indicator is lit.
has been loaded properly.
(page 29).
paper roll.
paper roll.
switch to turn on the printer, this
indicator remains lit while the
printer is initializing. Wait until
initialization is complete.
to enter the standby state, press
the 1 On/standby switch again
to turn on the power, and then
check the ink ribbon and paper
roll.
to enter the standby state, and
then press the 1 On/standby
switch again to turn on the
power. If the printer is still
unable to recover from the
failure, press the 1 On/standby
switch to enter the standby state
and then disconnect the power
cord and contact your dealer.