Siemens SIPROTEC4 7SJ61 Protocol Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Control Unit
  5. SIPROTEC4 7SJ61
  6. Protocol manual

Siemens SIPROTEC4 7SJ61 Protocol Manual

Communication module profibus-dp bus mapping
Hide thumbs Also See for SIPROTEC4 7SJ61:
Table of Contents

Advertisement

Quick Links

SIPROTEC4
Multifunction protection with
control
7SJ61...63, 7SJ65
Input/Output unit with local
control
6MD63
Communication module
PROFIBUS-DP
Bus mapping
Revision: 2.1
Edition: October 2001
C53000-L1840-B006-02
Preface
Data in the PROFIBUS-DP
messages
Standard mapping 2-1
Standard mapping 2-2
Standard mapping 2-3
Standard mapping 2-4
Glossary
Index
Cover
1
2
3
4
5

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIPROTEC4 7SJ61

Summary of Contents for Siemens SIPROTEC4 7SJ61

  • Page 1 Preface Data in the PROFIBUS-DP messages SIPROTEC4 Standard mapping 2-1 Multifunction protection with Standard mapping 2-2 control Standard mapping 2-3 7SJ61...63, 7SJ65 Standard mapping 2-4 Input/Output unit with local control Glossary 6MD63 Index Communication module Cover PROFIBUS-DP Bus mapping Revision: 2.1 Edition: October 2001 C53000-L1840-B006-02...
  • Page 2 Registered trademarks Subject to change without prior notice. SIPROTECâ und DIGSIâ are registered trademarks of Siemens AG. Other designations in this manual may be trademarks that if used by third parties for their own purposes may violate the rights of the owner.
  • Page 3 Preface The manual is devided into the following topics: Contents of this manual • Data in the PROFIBUS-DP messages • Standard mapping 2-1 • Standard mapping 2-2 • Standard mapping 2-3 • Standard mapping 2-4 This manual describes the data in the PROFIBUS-DP messages of the Additional SIPROTEC devices 7SJ61...7SJ63, 7SJ65, 6MD63.
  • Page 4 See our catalog of courses for a list of available courses or contact our Training courses Training center in Nuremberg. Questions If you have questions to the SIPROTEC devices, contact your Siemens representative. 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping C53000-L1840-B006-02...
  • Page 5 Revision index Modified chapters / Edition Reasons of modification pages First edition, Doc.-No.: C53000-L1840-B006-02 Aug 23 , 2000 • Document also valid for 7SJ65 devices • chap. 4.2.3.1 Allocation 3/0...3/7 for Standard mapping 2-3 corrected • chap. 5 Standard mapping 2-4 added chap.
  • Page 6 Revision index 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping C53000-L1840-B006-02...

  • Page 7: Table Of Contents

    Table of contents Data in the PROFIBUS-DP messages................1-1 Explanation..................... 1-1 Messages in output direction: PROFIBUS-DP master to the SIPROTEC device ......................1-3 Messages in input direction: SIPROTEC device to the PROFIBUS-DP master ......................1-3 1.3.1 Annunciations....................1-3 1.3.2 Measured values .................... 1-4 1.3.3 Metered measurands ..................
  • Page 8 Table of contents 2.2.1.5 Diagnosis........................2-5 2.2.1.6 Automatic recloser status ....................2-6 2.2.1.7 Time overcurrent protection..................2-6 2.2.1.8 Directional time overcurrent protection................2-7 2.2.1.9 Unbalanced load protection..................2-7 2.2.1.10 Frequency protection ....................2-7 2.2.1.11 Undervoltage and overvoltage protection ..............2-8 2.2.1.12 Sensitive ground fault protection.................2-8 2.2.1.13 Circuit breaker failure protection .................2-8 2.2.1.14 Thermal overload protection ..................2-9 2.2.1.15...
  • Page 9 3.2.1.15 Cold load pickup ......................3-8 3.2.1.16 Measurement supervision...................3-8 3.2.1.17 Set point alarms ......................3-8 3.2.1.18 Status annunciations ....................3-9 3.2.2 Measured values ..................3-10 3.2.2.1 Recorded measured values ..................3-10 3.2.2.2 Measured values – mean values................3-10 3.2.3 Metered measurands ................... 3-10 Standard mapping 2-3 ....................4-1 Message in output direction ................
  • Page 10 Table of contents 5.2.1.5 Sensitive ground fault protection ................5-14 5.2.1.6 Thermal overload protection..................5-14 5.2.1.7 Directional time overcurrent protection..............5-14 5.2.1.8 Diagnosis........................5-14 5.2.2 Measured values ..................5-15 5.2.3 Metered measurands ................... 5-15 Glossary .......................... 6-1 Index ..........................7-1 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping viii C53000-L1840-B006-02...

  • Page 11: Data In The Profibus-Dp Messages

    Data in the PROFIBUS-DP messages Data in the PROFIBUS-DP messages Explanation Note The examples shown in this chapter 1.1 do not necessarily correspond to the real allocation of the objects in the bus mapping. The chapters 2 to 5 define the data area of the PROFIBUS-DP messages for data transfer between the PROFIBUS-DP slave of the SIPROTEC device 7SJ61...7SJ63, 7SJ65, 6MD63 with the PROFIBUS- DP master.
  • Page 12 Data in the PROFIBUS-DP messages Bit variables The offset indicates the byte, which contains the bit value and the position of bit 0 of the bit variable, e.g. (input message): (SP/SC, DP/DC) Offset Designation of the Comments Internal SIPROTEC objects object no.

  • Page 13: Messages In Output Direction: Profibus-Dp Master To The Siprotec Device

    Data in the PROFIBUS-DP messages Messages in output direction: PROFIBUS-DP master to the SIPROTEC device The messages in PROFIBUS-DP output direction (ref. to chap. 2.1, 3.1, 4.1 and 5.1) allow: • command outputs through the output relays of the SIPROTEC device (external commands), •...

  • Page 14: Measured Values

    Data in the PROFIBUS-DP messages 1.3.2 Measured values Note Depending on the device composition not all of the indicated analog inputs (and corresponding PROFIBUS-DP message positions) may be available in the SIPROTEC device. The given scaling values for the measured values in the standard mappings apply to installations with the following nominal operating values: Nominal operating voltage of primary equipment (parameter address 1101):...

  • Page 15: Metered Measurands

    Data in the PROFIBUS-DP messages 1.3.3 Metered measurands Scaling The scaling of the metered measurands, which are derived from measured values, refers to: 60000 impulses per hour for V = V and I = I OMINAL OPERATING VOLTAGE OF PRIMARY EQUIPMENT (parameter address = 1101) OMINAL OPERATING CURRENT OF PRIMARY EQUIPMENT (parameter address = 1102)

  • Page 16: Configuration Data Of The Standard Mappings 2-1 To 2-4

    Data in the PROFIBUS-DP messages Configuration data of the standard mappings 2-1 to 2-4 There are three standard mappings (standard mapping 2-1 to standard mapping 2-4) available for the SIPROTEC devices 7SJ61...7SJ63, 7SJ65, 6MD63 for parameterization with DIGSI version 4.2 or higher which differ in the data size of the PROFIBUS-DP messages.
  • Page 17 Data in the PROFIBUS-DP messages Standard The standard mapping 2-4 contains: mapping 2-4 Output direction: • 3 double-point commands • 5 single-point commands Input direction: • 3 double-point indications • 26 single-point indications • 8 measured values (integer) • 2 metered measurands (unsigned long) PROFIBUS-DP Standard mapping 2-1: 1FH 1FH 1FH 1FH 1FH 1FH 13H 28H configuration data...
  • Page 18 Data in the PROFIBUS-DP messages Standard mapping 2-3: Module Order number Input Output address address Input – 16 Bytes Addr_Ix Input – 16 Bytes Addr_Ix+16 Input – 16 Bytes Addr_Ix+32 Input – 16 Bytes Addr_Ix+48 Input – 16 Bytes Addr_Ix+64 Output –...
  • Page 19 Data in the PROFIBUS-DP messages The DIGSI 4.1 standard mappings are not component of this documentation. You find associated information in the following manuals: Manual Contents Order number PROFIBUS-DP C53000-L1840-B002-01 Data in the PROFIBUS-DP messages Bus mapping of the SIPROTEC device 7SJ61 7SJ61 PROFIBUS-DP C53000-L1840-B003-01...

  • Page 20: Notes To Siprotec Objects

    Data in the PROFIBUS-DP messages Notes to SIPROTEC objects This chapter contains notes for the use and evaluation of certain SIPROTEC objects. The description of the standard mappings (ref. to chap. 2 to 5) contains the pre-allocation of the mapping files at delivery or first assignment of a mapping in DIGSI to the SIPROTEC device.

  • Page 21: Control Mode Remote

    Data in the PROFIBUS-DP messages 1.5.2 Control mode REMOTE Control mode with control authority is REMOTE, option of unlocked control with PROFIBUS-DP. • Changing the “Control mode REMOTE“ to UNLOCKED permits one unlocked control operation via PROFIBUS-DP. After execution of the command, the “Control mode REMOTE“...

  • Page 22: Cfc-Incoming Annunciations

    Data in the PROFIBUS-DP messages 1.5.4 CFC-Incoming annunciations The CFC-Incoming annunciations allow routing of further protection annunciations on PROFIBUS-DP, which are not contained in the standard mapping (e.g. ">BLK 50/51", internal object number = 1704 or ">BLK 50N/51N", internal object number = 1714). You find information about this in the manual "7SJ61...63, 7SJ65, 6MD63, 7UM61 PROFIBUS-DP - Communication profile"...

  • Page 23: Alarm Summary Event

    Data in the PROFIBUS-DP messages 1.5.6 Alarm summary event The "Alarm summary event" is indicated, if at least one of the following internal alarms assumes the ON status: • "Failure: Current summation“, "Failure: Current balance“, "Failure: Voltage balance“, "Failure: Phase sequence current“, "Failure: Phase sequence voltage“.

  • Page 24: Using Device Firmware Version 4.3 Or Higher

    Data in the PROFIBUS-DP messages Using device firmware version 4.3 or higher The following SIPROTEC objects are no longer included per default in the parameter set of the device. Double commands: • Switching device D1 (UsrDC1) ... Switching device D3 (UsrDC3) Single commands: •...

  • Page 25: Standard Mapping 2-1

    Standard mapping 2-1 Standard mapping 2-1 Message in output direction 2.1.1 Double commands (with checkback indication) • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Impulse output, – 3 relays (2-pole On, 1-pole Off) Q0 ON/OFF Q1 ON/OFF Impulse output,...

  • Page 26: Internal Commands

    Standard mapping 2-1 Offset Designation of the Internal Comments SIPROTEC objects object no. Output channel E3 (UsrSC10) Continuous output without restauration, – 1 relay, 1-pole Output channel E3 (UsrSC10) 2.1.3 Internal commands • Ref. to chap. 1.5.2 and 1.5.3 for additional notes regarding "Control mode REMOTE" and "Changing the setting group".
  • Page 27 Standard mapping 2-1 Offset Designation of the Internal Comments SIPROTEC objects object no. CFC-Incoming annunciation 2 (UsCfcSpI2) OFF Tagging ON/OFF, released as CFC input – CFC-Incoming annunciation 2 (UsCfcSpI2) ON CFC-Incoming annunciation 3 (UsCfcSpI3) OFF Tagging ON/OFF, released as CFC input –...

  • Page 28: Message In Input Direction

    Standard mapping 2-1 Message in input direction 2.2.1 Annunciations 2.2.1.1 Double commands – checkback signals • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Double-point indication ON/OFF – Q0 ON/OFF Q1 ON/OFF Double-point indication ON/OFF –...

  • Page 29: Diagnosis

    Standard mapping 2-1 Offset Designation of the Comments Internal SIPROTEC objects object no. Input channel 4 (UsrSpO/O12) Single-point indication ON/OFF – Input channel 5 (UsrSpO/O13) Single-point indication ON/OFF – Input channel 6 (UsrSpO/O14) Single-point indication ON/OFF – Input channel 7 (UsrSpO/O32) Tagging / Internal single-point indication ON/OFF –...

  • Page 30: Automatic Recloser Status

    Standard mapping 2-1 Offset Designation of the Comments Internal SIPROTEC objects object no. Relay PICKUP 1 = Relay PICKUP (protection, summary alarm) Relay TRIP 1 = Relay GENERAL TRIP command (common, summary alarm) <reserved> – 2.2.1.6 Automatic recloser status Offset Designation of the Comments Internal...

  • Page 31: Directional Time Overcurrent Protection

    Standard mapping 2-1 2.2.1.8 Directional time overcurrent protection Offset Designation of the Comments Internal SIPROTEC objects object no. Phase A forward 1 = Phase A forward 2628 Phase B forward 1 = Phase B forward 2629 Phase C forward 1 = Phase C forward 2630 Phase A reverse 1 = Phase A reverse...

  • Page 32: Undervoltage And Overvoltage Protection

    Standard mapping 2-1 Offset Designation of the Comments Internal SIPROTEC objects object no. 12/2 81-3 TRIP 1 = 81-1 TRIP 5238 12/3 81-4 TRIP 1 = 81-1 TRIP 5239 2.2.1.11 Undervoltage and overvoltage protection Offset Designation of the Comments Internal SIPROTEC objects object no.

  • Page 33: Thermal Overload Protection

    Standard mapping 2-1 2.2.1.14 Thermal overload protection Offset Designation of the Comments Internal SIPROTEC objects object no. 15/0 49 O/L OFF 1 = Thermal overload protection is switched OFF 1511 15/1 49 O/L I Alarm 1 = 49 Overload current alarm (I alarm) 1515 15/2 49 O/L <Theta>...

  • Page 34: Measurement Supervision

    Standard mapping 2-1 2.2.1.19 Measurement supervision Offset Designation of the Comments Internal SIPROTEC objects object no. 17/2 Fail I Superv. 1 = Failure: General current supervision 17/3 Failure <Sum>I 1 = Failure: Current summation 17/4 Fail Ph. Seq. 1 = Failure: Phase sequence 17/5 MeasSup OFF 1 = Measurement supervision is switched OFF...

  • Page 35: Measured Values

    Standard mapping 2-1 2.2.2 Measured values • Ref. to chap. 1.3.2 for additional notes regarding scaling of measured values. 2.2.2.1 Recorded measured values Offset Designation of the Comments Scaling Internal SIPROTEC objects (32767 corresponds to ...) object no. Ia = 3276.7 A Ib = 3276.7 A...

  • Page 36: Fault Locator

    Standard mapping 2-1 2.2.3 Fault locator • Ref. to chap. 1.5.8 for additional notes. Offset Designation of the Comments Scaling Internal SIPROTEC objects (32767 corresponds to ...) object no. dist = Fault locator: 3276.7 km/miles 1119 Distance to fault (Fault location) 2.2.4 Metered measurands •...

  • Page 37: Standard Mapping 2-2

    Standard mapping 2-2 Standard mapping 2-2 Message in output direction 3.1.1 Double commands (with checkback indication) • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Impulse output, – 3 relays (2-pole On, 1-pole Off) Q0 ON/OFF Q1 ON/OFF Impulse output,...

  • Page 38: Internal Commands

    Standard mapping 2-2 Offset Designation of the Internal Comments SIPROTEC objects object no. Output channel E3 (UsrSC10) Continuous output without restauration, – 1 relay, 1-pole Output channel E3 (UsrSC10) 3.1.3 Internal commands • Ref. to chap. 1.5.2 and 1.5.3 for additional notes regarding "Control mode REMOTE" and "Changing the setting group".
  • Page 39 Standard mapping 2-2 Offset Designation of the Internal Comments SIPROTEC objects object no. CFC-Incoming annunciation 2 (UsCfcSpI2) OFF Tagging ON/OFF, released as CFC input – CFC-Incoming annunciation 2 (UsCfcSpI2) ON CFC-Incoming annunciation 3 (UsCfcSpI3) OFF Tagging ON/OFF, released as CFC input –...

  • Page 40: Message In Input Direction

    Standard mapping 2-2 Message in input direction 3.2.1 Annunciations 3.2.1.1 Double commands – checkback signals • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Double-point indication ON/OFF – Q0 ON/OFF Q1 ON/OFF Double-point indication ON/OFF –...

  • Page 41: Application Logic Cfc

    Standard mapping 2-2 Offset Designation of the Comments Internal SIPROTEC objects object no. Input channel 3 (UsrSpO/O11) Single-point indication ON/OFF – Input channel 4 (UsrSpO/O12) Single-point indication ON/OFF – Input channel 5 (UsrSpO/O13) Single-point indication ON/OFF – Input channel 6 (UsrSpO/O14) Single-point indication ON/OFF –...

  • Page 42: Automatic Recloser Status

    Standard mapping 2-2 Offset Designation of the Comments Internal SIPROTEC objects object no. Alarm Sum Event 1 = Alarm summary event ON Relay PICKUP 1 = Relay PICKUP (summary alarm) Relay TRIP 1 = Relay GENERAL TRIP command (summary alarm) <reserved>...

  • Page 43: Unbalanced Load Protection

    Standard mapping 2-2 3.2.1.8 Unbalanced load protection Offset Designation of the Comments Internal SIPROTEC objects object no. 46 OFF 1 = Unbalanced load protection is switched OFF 5151 46 TRIP 1 = 46 TRIP 5170 3.2.1.9 Sensitive ground fault protection Offset Designation of the Comments...

  • Page 44: Trip Coil Monitor

    Standard mapping 2-2 Offset Designation of the Comments Internal SIPROTEC objects object no. 11/2 Rotor locked 1 = Rotor locked 6822 11/3 START-SUP pu 1 = Startup supervision Pickup 6823 3.2.1.14 Trip coil monitor Offset Designation of the Comments Internal SIPROTEC objects object no.

  • Page 45: Status Annunciations

    Standard mapping 2-2 3.2.1.18 Status annunciations • Ref. to chap. 1.5.7 for additional notes regarding "Stop data transmission". Offset Designation of the Comments Internal SIPROTEC objects object no. 14/0 >No Volt 1 = Binary input “No voltage (fuse blown)" is active –...

  • Page 46: Measured Values

    Standard mapping 2-2 3.2.2 Measured values • Ref. to chap. 1.3.2 for additional notes regarding scaling of measured values. 3.2.2.1 Recorded measured values Offset Designation of the Comments Scaling Internal SIPROTEC objects (32767 corresponds to ...) object no. Ia = 3276.7 A Ib = 3276.7 A...

  • Page 47: Standard Mapping 2-3

    Standard mapping 2-3 Standard mapping 2-3 Message in output direction 4.1.1 Double commands (with checkback indication) • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Impulse output, – 3 relays (2-pole ON, 1-pole OFF) Q0 ON/OFF Q1 ON/OFF Impulse output,...

  • Page 48: Internal Commands

    Standard mapping 2-3 Offset Designation of the Internal Comments SIPROTEC objects object no. Output channel E2 (UsrSC6) Impulse output, – 1 relay, 1-pole Output channel E2 (UsrSC6) Output channel E3 (UsrSC14) Impulse output, – Output channel E3 (UsrSC14) 1 relay, 1-pole Output channel E4 (UsrSC15) Impulse output, –...
  • Page 49 Standard mapping 2-3 Offset Designation of the Internal Comments SIPROTEC objects object no. CFC-Incoming annunciation 6 (UsCfcSpI6) OFF Tagging ON/OFF, released as CFC input – CFC-Incoming annunciation 6 (UsCfcSpI6) ON CFC-Incoming annunciation 7 (UsCfcSpI7) OFF Tagging ON/OFF, released as CFC input –...

  • Page 50: Message In Input Direction

    Standard mapping 2-3 Message in input direction 4.2.1 Annunciations 4.2.1.1 Double commands – checkback signals • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Double-point indication ON/OFF – Q0 ON/OFF Q1 ON/OFF Double-point indication ON/OFF –...

  • Page 51: Input Channels With Allocation To The Binary Inputs And Tagging

    Standard mapping 2-3 4.2.1.3 Input channels with allocation to the binary inputs and tagging • Ref. to chap. 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. Input channel 1 (UsrSpO/C1) Single-point indication OPEN/CLOSE – Input channel 2 (UsrSpO/C2) Single-point indication OPEN/CLOSE –...

  • Page 52: Diagnosis

    Standard mapping 2-3 4.2.1.5 Diagnosis • Ref. to chap. 1.5.5 and 1.5.6 for additional notes regarding "Error with a summary alarm" and "Alarm summary event". Offset Designation of the Comments Internal SIPROTEC objects object no. Device OK 1 = Update of the device replica in the SIPROTEC device completed after initial start or restart <reserved>...

  • Page 53: Status Annunciations

    Standard mapping 2-3 4.2.1.8 Status annunciations • Ref. to chap. 1.5.7 for additional notes regarding "Stop data transmission". Offset Designation of the Comments Internal SIPROTEC objects object no. >No Volt 1 = Binary input “No voltage (fuse blown)" is active –...

  • Page 54: Measured Values

    Standard mapping 2-3 4.2.2 Measured values • Ref. to chap. 1.3.2 for additional notes regarding scaling of measured values. 4.2.2.1 Recorded measured values Offset Designation of the Comments Scaling Internal SIPROTEC objects (32767 corresponds to ...) object no. Ia = 3276.7 A Ib = 3276.7 A...

  • Page 55: Metered Measurands

    Standard mapping 2-3 4.2.3 Metered measurands • Ref. to chap. 1.3.3 for additional notes regarding scaling of metered measurands. Offset Designation of the Comments Scaling Internal SIPROTEC objects -1 of the unsigned long- object no. value corresponds to ...) Wp(puls) = Pulsed Energy Wp (active) -1 impulses (metering impulses at binary input)
  • Page 56 Standard mapping 2-3 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping 4-10 C53000-L1840-B006-02...

  • Page 57: Standard Mapping 2-4

    Standard mapping 2-4 Standard mapping 2-4 Message in output direction 5.1.1 Double commands (with checkback indication) Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Impulse output, – Q0 ON/OFF 3 relays (2-pole ON, 1-pole OFF) Q1 ON/OFF Impulse output, –...

  • Page 58: Application Logic Cfc

    Standard mapping 2-4 5.1.4 Application logic CFC • Ref. to chap. 1.5.4 and 1.6 for additional notes. Offset Designation of the Comments Internal SIPROTEC objects object no. CFC-Incoming annunciation 1 (UsCfcSpI1) OFF Tagging ON/OFF, released as CFC input – CFC-Incoming annunciation 1 (UsCfcSpI1) ON CFC-Incoming annunciation 2 (UsCfcSpI2) OFF...

  • Page 59: Message In Input Direction

    Standard mapping 2-4 Message in input direction 5.2.1 Annunciations 5.2.1.1 Double commands – checkback signals Offset Designation of the Comments Internal SIPROTEC objects object no. Q0 ON/OFF Double-point indication ON/OFF – Q0 ON/OFF Q1 ON/OFF Double-point indication ON/OFF – Q1 ON/OFF Q8 ON/OFF Double-point indication ON/OFF –...

  • Page 60: Sensitive Ground Fault Protection

    Standard mapping 2-4 5.2.1.5 Sensitive ground fault protection Offset Designation of the Comments Internal SIPROTEC objects object no. 50Ns-2 TRIP 1 = 50Ns-2 TRIP 1223 50Ns-1 TRIP 1 = 50Ns-1 TRIP 1226 5.2.1.6 Thermal overload protection Offset Designation of the Comments Internal SIPROTEC objects...

  • Page 61: Measured Values

    Standard mapping 2-4 5.2.2 Measured values • Ref. to chap. 1.3.2 for additional notes regarding scaling of measured values. Offset Designation of the Comments Scaling Internal SIPROTEC objects (32767 corresponds to ...) object no. Va-b = Va-b 32.767 kV Ia = 3276.7 A Ib = 3276.7 A...
  • Page 62 Standard mapping 2-4 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping 5-16 C53000-L1840-B006-02...

  • Page 63: Glossary

    PROFIBUS Nutzerorganisation PROFIBUS - Decentralized Peripherals PROFIBUS-DP PROFIBUS interface module with (electrical) isolated RS485 interface for the SIPROTEC devices from Siemens. PROFIBUS interface module with optical interface for the SIPROTEC devices from Siemens. Single Command Single-point Indication 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping...
  • Page 64 Glossary 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping C53000-L1840-B006-02...

  • Page 65: Index

    Index Index Numerics 27 ..............2-8 Fault locator ..........2-12 37-1 Undercurrent alarm....3-8, 4-6 Frequency protection ........ 2-7 46 ............2-7, 3-7 49 ..........2-9, 3-7, 5-14 50/51 ........2-6, 3-6, 5-13 Measured values ... 1-4, 2-11, 3-10, 4-8, 5-15 50BF ..........2-8, 3-7 Measurement supervision ......
  • Page 66 Index 7SJ61...7SJ63, 7SJ65, 6MD63 PROFIBUS-DP – Bus mapping C53000-L1840-B006-02...

This manual is also suitable for:

Siprotec4 7sj62Siprotec4 7sj63Siprotec4 7sj65Siprotec4 6md63

Table of Contents