Advertisement
■ Guide cap
■ Guide cap
To guide collector arms via turntables or traversers.
To guide collector arms via turntables or traversers.
1. Mount the bracket to an Ⅰ-beam or other building
1. Mount the bracket to an Ⅰ-beam or other building
structure. Distances (A) from the Ⅰ-beam and the
structure. Distances (A) from the Ⅰ-beam and the
mounting interval are as shown in the right
mounting interval are as shown in the right
description.
description.
2. Drill a φ5mm hole 20mm away from the end of the
2. Drill a φ5mm hole 20mm away from the end of the
Tro-Reel unit. Be sure to use a file of φ5 size.
Tro-Reel unit. Be sure to use a file of φ5 size.
3. Place the guide cap and secure it with a knock pin.
3. Place the guide cap and secure it with a knock pin.
4. Fit on the cover.
4. Fit on the cover.
Bracket for retaining tension
Bracket for retaining tension
(bracket used for when tension is applied)
(bracket used for when tension is applied)
φ11mm hole
φ11mm hole
Hanger bracket
Hanger bracket
(bracket used when no
(bracket used when no
tension is applied)
tension is applied)
φ11mm hole
φ11mm hole
Notes
Notes
Use a tandem-type collector
Use a tandem-type collector
●
●
arm and set the traveling
arm and set the traveling
speed for switching sections
speed for switching sections
to 60m/min. or less.
to 60m/min. or less.
Be sure to use only the
Be sure to use only the
●
●
specified dimensions for each
specified dimensions for each
mounting part.
mounting part.
Failure to do so may cause poor
Failure to do so may cause poor
collector arm contact or
collector arm contact or
separation from wires.
separation from wires.
In the case using at outdoors,
In the case using at outdoors,
●
●
Please contact Pansonic
Please contact Pansonic
Electric Works Co.,Ltd.
Electric Works Co.,Ltd.
Mount the cover by all means.
Mount the cover by all means.
●
●
Failure to do so may cause
Failure to do so may cause
electric shock.
electric shock.
■ Insulating piece
■ Insulating piece
To Separate circuits electrically.
To Separate circuits electrically.
1.Drill a Φ5mm hole 20mm
1.Drill a Φ5mm hole 20mm
away from each end of the
away from each end of the
Tro-Reel unit
Tro-Reel unit
2.Mount an insulating piece
2.Mount an insulating piece
and secure it with a knock
and secure it with a knock
pin.Be sure to place a
pin.Be sure to place a
knock pin securely. Failure
knock pin securely. Failure
to do so may cause
to do so may cause
damage due to falling of
damage due to falling of
equipment.
equipment.
3.Fit on the cover.
3.Fit on the cover.
Notes
Notes
Mount the cover by all means.
Mount the cover by all means.
●
●
Failure to do so may cause electric shock.
Failure to do so may cause electric shock.
<300A>
<300A>
●
●
Since there is a gap between the insulating piece
Since there is a gap between the insulating piece
and the sliding surface of the Tro-Reel unit, the end
and the sliding surface of the Tro-Reel unit, the end
of the Tro-Reel unit must be chamfered as shown at
of the Tro-Reel unit must be chamfered as shown at
right.
right.
Failure may cause bad contact or collector arm derailing.
Failure may cause bad contact or collector arm derailing.
Type
Type
Hanger bracket
Hanger bracket
Bracket for retaining tension
Bracket for retaining tension
Attach two standard
Attach two standard
hangers in parallel.
hangers in parallel.
I-beam
I-beam
Cover
Cover
Guide Cap
Guide Cap
I-beam
I-beam
φ5mm hole
φ5mm hole
knock pin
knock pin
(φ5×18)
(φ5×18)
Notes
Notes
<Mounting to 300A Tro-Reel unit>
<Mounting to 300A Tro-Reel unit>
Since there is a gap between the guide
Since there is a gap between the guide
●
●
cap and the sliding surface to the
cap and the sliding surface to the
Tro-Reel unit, the end of the Tro-Reel unit
Tro-Reel unit, the end of the Tro-Reel unit
must be chamfered as shown right.
must be chamfered as shown right.
Failure may cause bad contact or collector
Failure may cause bad contact or collector
arm derailing.
arm derailing.
Cover
Cover
Insulating piece
Insulating piece
Knock pin (φ5×18mm)
Knock pin (φ5×18mm)
ー 25 ー
Angle dimensions
Angle dimensions
A size
A size
for 3P
for 3P
-40×40×5
-40×40×5
250〜300mm
250〜300mm
100×50×5
100×50×5
Bracket for retaining tension (bracket used for when tensionis applied)
Bracket for retaining tension (bracket used for when tensionis applied)
Guide cap
Guide cap
Hanger bracket
Hanger bracket
(bracket used when no tension is applied)
(bracket used when no tension is applied)
Standard hanger
Standard hanger
Tro-Reel unit
Tro-Reel unit
approx.5mm
approx.5mm
φ5mm hole (for knock pin)
φ5mm hole (for knock pin)
Tro-Reel unit
Tro-Reel unit
approx.5mm
approx.5mm
B size
B size
Minimum Standard
Minimum Standard
75mm
75mm
100mm
100mm
Tro-Reel unit
Tro-Reel unit
Guide cap
Guide cap
Sliding surface of the Tro-Reel unit
Sliding surface of the Tro-Reel unit
Cover
Cover
Insulating piece
Insulating piece
Tro-Reel unit
Tro-Reel unit
Insulating piece
Insulating piece
Sliding surface of
Sliding surface of
the Tro-Reel unit
the Tro-Reel unit
Advertisement
