ekwb EK-Supremacy Classic RGB User Manual

ekwb EK-Supremacy Classic RGB User Manual

Cpu water block

Advertisement

Quick Links

EK-Supremacy Classic RGB
CPU WATER BLOCK
USER GUIDE
1st Revision, October 27th 2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EK-Supremacy Classic RGB and is the answer not in the manual?

Questions and answers

Summary of Contents for ekwb EK-Supremacy Classic RGB

  • Page 1 EK-Supremacy Classic RGB CPU WATER BLOCK USER GUIDE 1st Revision, October 27th 2018...
  • Page 2 The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
  • Page 3: Table Of Contents

    TABLE OF CONTENT GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY WHAT IS ENCLOSED QUICK INSTALLATION GUIDE INSTALLING THE WATER BLOCK LGA-20XX SOCKET MOTHERBOARDS LGA-115X SOCKET MOTHERBOARDS AMX AND FMX SOCKET MOTHERBOARDS CONNECTING THE RGB LED STRIP CONNECTING THE RGB LED STRIP SUPPORT AND SERVICE SOCIAL MEDIA - 3 -...
  • Page 4: General Information On Water Block Compatibility

    WHAT IS ENCLOSED a) EK-CPU Classic RGB – Nickel + Plexi CPU water block: b) EK-Supremacy Classic RGB - AMD Nickel + Plexi water block: - EK-CPU Supremacy Classic RGB – Nickel + Plexi CPU - EK-CPU Supremacy Classic RGB – Nickel + Plexi CPU water block.
  • Page 5: Installing The Water Block

    INSTALLING THE WATER BLOCK LGA-20XX SOCKET MOTHERBOARDS LGA-20XX M3 LGA-20XX M3 Thumb Screw STEP 1 Thumb Screw Prepare the foil bag with mounting mechanism, which is enclosed with the CPU water block delivery. Install four (4) specific LGA-20XX M3 thumb screws into four M3 threaded stubs on the LGA-20XX socket integrated latch mechanism (ILM).
  • Page 6 Fitting Barb The installation of the CPU water block is now complete. Inlet port With EK-Supremacy Classic RGB series water blocks it is mandatory to use the port that is nearest to the center Outlet port of the water block as INLET port. Mixing the ports may result in less than ideal thermal performance of the water block.
  • Page 7: Lga-115X Socket Motherboards

    LGA-115x SOCKET MOTHERBOARDS STEP 1 If already installed, please remove the motherboard from your computer and place it on an even surface with front facing down. STEP 2 Preparing backplate rubber gasket The enclosed rubber gasket is essential part of the backplate and mounting system and must be used every time you install this water block on your motherboard.
  • Page 8: Amx And Fmx Socket Motherboards

    STEP 4 M3 Thumb Install four (4) M3 thumb screws onto your motherboard. It is Screw mandatory to put 0.7mm plastic washer underneath each of the M3 thumb screws. Tighten the screws to the metal backplate until you reach the end of the thread. Using tools (such as pliers) is not recommended.
  • Page 9 STEP 2 Prepare the foil bag with mounting mechanism, which is enclosed with the CPU water block delivery. Install four (4) M3 thumb screws onto your motherboard. It is man- datory to put plastic AM4 standoff underneath each of the M3 thumb screws.
  • Page 10: Connecting The Rgb Led Strip

    CONNECTING THE RGB LED STRIP CONNECTING THE RGB LED STRIP STEP 1 Plug the 4-pin connector from Water block’s LED light to the RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +12V G R B. Please ensure that the arrow indicated on the connector is plugged into the +12V line as indicated on your motherboard.
  • Page 11: Support And Service

    SUPPORT AND SERVICE For assistance please contact: http://support.ekwb.com/ EKWB d.o.o. Pod lipami 18 1218 Komenda Slovenia - EU SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks...

This manual is also suitable for:

38311098136213831109813799

Table of Contents