Operation - Worx WG154 Manual

ASSEMBLY
1. ASSEMBLY OF THE MAIN HANDLE (See Fig.
A)
Align and insert the shaft into the upper housing
until a click can be heard. Make sure the grooves are
correctly matched (See Fig. A).
NOTE: Make sure that the handle is firmly
locked in place. Do not try to remove these
pieces after connecting.
2. ASSEMBLY OF THE SAFETY GUARD (See
Fig. B1, B2)
Remove a screw from the guard; attach the safety
guard to the trimmer head. Align the guard so it
slides into the slots located on the trimmer head.
Turn the tool over and secure the safety guard onto
the trimmer head with the screw (a) provided.
OPERATION INSTRUCTIONS
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
1. BEFORE USING YOUR CORDLESS GRASS
TRIMMER
The battery pack included is shipped UNCHARGED.
You must charge before first use.
The battery charger supplied was designed to only
charge the Li-Ion battery also supplied. Do not use
another battery charger.
2. CHARGING YOUR BATTERY PACK
The Li-Ion battery is protected against deep
discharging. When the battery is empty, the machine
will switch off by means of a protective circuit: The
trimmer head will no longer rotate .
In a warm environment or after heavy use, the
battery pack may become too hot to permit charging.
Allow time for the battery to cool down before
recharging.
3. TO REMOVE OR INSTALL BATTERY PACK
(See Fig. C1, C2)
Depress the battery release button to release battery
pack from your trimmer (Fig. C1). After recharging,
insert the battery pack into trimmer's battery port
(Fig. C2). A simple push and slight pressure will be
sufficient until a click is heard.
NOTE: When removing the battery pack, hold it
firmly to avoid potential accidents.
2 in 1: Trimmer / Edger
4. SAFETY ON/OFF SWITCH (See Fig. D)
The safety switch is locked off to prevent accidental
starting. Depress the lock off button (2) then depress
the on/off switch (3) and release lock off button. Your
trimmer is now on. To switch off, just release the on/
off switch.
WARNING! The cutting head continues to
rotate after the trimmer has been
switched off; wait until it has completely
stopped then lay down the tool.

OPERATION

WARNING: Always wear the eye protection.
Never lean over the trimmer head. Rocks or
debris can ricochet or be thrown into eyes and face
and cause blindness or other serious injury. When
operating unit, check for the following:
Wear eye protection and heavy clothing. Hold front
handle with one hand and auxiliary handle with
the other hand. Keep unit below waist level. Work
only from your right to your left to ensure debris is
thrown away from you. Without bending over, keep
line near and parallel to the ground (perpendicular
when edging) and not crowded into material being
cut.
WARNING: Make sure that line is fed out
before operation. Make sure motor is up
to full speed before trimming.
WARNING: Use only 0.065 inches (1.65
mm) diameter cutting line. Other sizes of
line will not feed properly and will result in improper
cutting head function or can cause serious injury. Do
not use other material such as wire, string, rope, etc.
Wire can break off during cutting and become a
dangerous projectile that can cause serious injury.
FLOWER GUARD (See Fig. E)
Push the Flower Guard (6) in when edging and
pull it out before trimming, as shown in Fig.
E. Before trimming or edging make sure the
Flower Guard is locked firmly in position.
TRIMMING (See Fig. E1)
Postion the trimmer head as shown in Fig. E1 for
trimming.
Keep the bottom of the trimmer head just above the
ground and at an angle. Allow only the tip of line to
make contact. Do not force trimmer line into work
area.
EDGING (See Fig. E2, E3, E4)
ALWAYS REMOVE THE BATTERY PACK
BEFORE ADJUSTING THE TRIMMER HEAD
POSITION
For edging, position the trimmer head as Fig. E2.
9
EN