Download Print this page
Freescale Semiconductor USB-KW24D512 Quick Start Manual

Freescale Semiconductor USB-KW24D512 Quick Start Manual

Usb packet sniffer/dongle for kinetis mkw22d and mkw24d wireless mcus

Advertisement

Quick Links

Quick Start Guide
USB Packet Sniffer/Dongle
for Kinetis MKW22D and
MKW24D Wireless MCUs
USB-KW24D512

Advertisement

loading
Need help?

Need help?

Do you have a question about the USB-KW24D512 and is the answer not in the manual?

Questions and answers

Summary of Contents for Freescale Semiconductor USB-KW24D512

  • Page 1 Quick Start Guide USB Packet Sniffer/Dongle for Kinetis MKW22D and MKW24D Wireless MCUs USB-KW24D512...
  • Page 2 Quick Start Guide Get to Know the USB-KW24D512 Application Button Reset LEDs Antenna Button USB Connector Mini-JTAG MKW2xIC (10-pin)
  • Page 3 Introduction The USB-KW24D512 Packet Sniffer/Dongle is dual use hardware in a convenient USB dongle form factor for part numbers MKW22D512 and MKW24D512. As delivered, the device is programmed with 802.15.4 packet sniffer software that interfaces with Freescale’s Test Tool Protocol Analyzer as well as most commercially available 802.15.4 packet sniffer programs.
  • Page 4 Quick Start Guide...
  • Page 5 USB-KW24D512 USB-KW24D512 Features • 50 MHz ARM Cortex -M4 based core ® ® • 512KB Flash, 64KB SRAM • Typical current consumption: 250 µA/MHz run, 1.7 µA RTC standby • IEEE-802.15.4 compliant • -102 dBM RX sensitivity and +8 dBm TX output power •...
  • Page 6 Quick Start Guide Step-by-Step Instructions In this quick start guide, you will learn how to enable and use the USB-KW24D512 device as a sniffer. You will also learn how to modify the existent firmware on the dongle for use as a development environment or network node.
  • Page 7 USB-KW24D512 Connect the Hardware Download Software Connect the USB-KW24D512 dongle to and Tools the PC. Allow the PC to automatically install the USB drivers if prompted. Download installation software and documentation under Drivers can be found under BeeKit’s “Jump Start Your Design”...
  • Page 8 1. Open Test Tool application. Go to <BeeKit installation folder>\Test Tool 12\Test Tool.exe 2. Select Protocol Analyzer. 3. Start capturing packets. The USB-KW24D512 dongle should be listed as “Devices: KW24 USB Dongle (COMx) Off” as shown in the image. Click on a channel number to start monitoring packets over the air on that channel.
  • Page 9 <BeeKit installation folder>\Test Tool flashed. 12\Test Tool.exe 2. Select Firmware Loaders --> Kinetis Firmware Loader option. 3. Connect a J-Link Flash programmer 7. Click on “OK” and wait for the upload to the mini-JTAG connector on the to finish. USB-KW24D512 board.
  • Page 10 4. Ensure you have selected the Option B: Using IAR Embedded Workbench J-Link/J-Trace driver under Download --> Debugger options. 1. Open a USB-KW24D512 project on IAR Embedded Workbench. 5. Click on “Download and Debug” to flash the board. 2. Compile and build the project.
  • Page 11: Additional Information

    USB-KW24D512 Additional Information For more information on USB-KW24D512 hardware and software, refer to BeeKit Wireless Connectivity Toolkit Quick Start Guide (BKWCTKQSG.pdf) to load sample applications using Zigbee, BeeStack Consumer (RF4CE) and IEEE 802.15.4 MAC ® protocol stacks.
  • Page 12: Get Started

    Quick Start Guide Get Started Download installation software and documentation under at freescale.com/USB-KW24D512. “Jump Start Your Design” Support Visit freescale.com/support for a list of phone numbers within your region. Warranty Visit freescale.com/warranty for complete warranty information. For more information, visit freescale.com/...