Download
Share
Print this page
  1. Manuals
  2. Brands
  3. HunterDouglas Manuals
  4. Window Blinds
  5. Luxaflex PowerView
  6. Reference manual

HunterDouglas Luxaflex PowerView Reference Manual

Irb roller blind
Hide thumbs

Advertisement

Quick Links

Download this manual
MANUAL
PowerView® IRB Roller Blind Reference-guide
Congratulations with the purchase of a Luxaflex® PowerView® Roller blind. This guide helps you get started with your
Roller blind powered by an integrated Li-ion battery.
1. Delivery condition
1.1. Pebble® or wand remote / Scene controller or Hub are purchased seperately
Pebble remote
Scene controller
Hub
Page 1 of 23
version: 1.0

Advertisement

loading

Related Manuals for HunterDouglas Luxaflex PowerView

Summary of Contents for HunterDouglas Luxaflex PowerView

  • Page 1 MANUAL PowerView® IRB Roller Blind Reference-guide Congratulations with the purchase of a Luxaflex® PowerView® Roller blind. This guide helps you get started with your Roller blind powered by an integrated Li-ion battery. 1. Delivery condition 1.1. Pebble® or wand remote / Scene controller or Hub are purchased seperately Pebble remote Scene controller Page 1 of 23...
  • Page 2 MANUAL 1.2. End limits factory set The top limit is set to the maximum roll-up The bottom limit is set to the ordered position product height 2. Special to the Integrated Rechargeable Battery motor 2.1 First Use When you will first use your motorized blind with integrated battery we advise to always first charge your blind. However when you receive your blind, it is in a so called hibernation status.
  • Page 3 MANUAL Manual motor Button USB Type-C Charging port LED status indicator 2.2 Charging When charging your blind, the blind/motor needs to be in an awake state. To wake up the blind please perform the following: Page 3 of 23 version: 1.0...
  • Page 4 MANUAL 2.2.1 Insert and extract USB type C charging plug. (like described at 2.1 First use) 2.2.2 Re-insert the USB -Type C connector to start charging. 2.2.3 The motor LED indicator will start blinking RED, signaling the charging process is activated. 2.2.4 When the LED turns green the integrated battery is fully charged.

  • Page 5: Getting Started

    MANUAL blinking CHARGE (normal) constant Fully Charged flashing CHARGE not allowed (temperature to high) Alternately CHARGE NTC ERROR (open/short circuit) 3. Getting started 3.1 Pairing a remote A PowerView® remote can control up to 6 individual groups of blinds (buttons 1 to 6 at the top of the remote). The instructions below assign the blind to group 1.
  • Page 6 MANUAL Press the  button. group1  IMPORTANT Watch out to perform steps 2.4 and 2.5 within 3 seconds! Press and hold the manual control button Press the  button. open The blind will jog 1x Release the manual control button Page 6 of 23 version: 1.0...
  • Page 7 MANUAL Press and hold the  button for 6 seconds. stop The remote will exit programming mode automatically after 20 seconds. Keep pressing until the remote lights stop blinking 4 Operating the blind 4.1. Selecting a blind Select 1 blind only Select 2 or more blinds Page 7 of 23 version: 1.0...
  • Page 8 MANUAL Select all blinds 4.2. Open / close a blind A. Select blind group B. Press  button open Page 8 of 23 version: 1.0...
  • Page 9 MANUAL C. Press  button close 4.3. Move a blind to a favourite position A. Select blind group B. Press  button favourite Page 9 of 23 version: 1.0...
  • Page 10 MANUAL 5. Set a favourite position Select the blind channel Use the  ,  and  open stop close buttons to move the blind to the desired favourite position. Use the  arrow up and  arrow down buttons to fine- tune.
  • Page 11 MANUAL Press and hold the manual control button Press the  button. favourite The blind will jog 1x to acknowledge the favourite position is set Release the manual control button The favourite position is set! Page 11 of 23 version: 1.0...

  • Page 12: Adjusting The End Limits

    MANUAL 6. Adjusting the end limits 6.1. New Top limit 6.1.1 Press and hold the manual control button 6.1.2 Press the  button. open Make sure  group1 on the remote is selected. The blind will jog 1x 6.1.3 Release the manual control button The motor LED turns red to acknowledge the motor is in program mode...
  • Page 13 MANUAL 6.1.4 Use the  ,  and  buttons to open stop close move the blind to the new top position. Use the  and  buttons to fine-tune. arrow up arrow down 6.1.5 Press and hold the  button for 6 seconds.
  • Page 14 MANUAL 6.1.7 Press the  button. open The blind will jog 1x to acknowledge the new limit is set 6.1.8 Release the manual control button The motor LED turns off 6.1.9 Press and hold the  button for 6 seconds. stop The remote will exit programming mode automatically after 20 seconds.
  • Page 15 MANUAL 6.1.10 The new top limit is set! 6.2. New Bottom limit 6.2.1 Press and hold the manual control button 6.2.2 Press the  button. close Make sure  on the remote is selected. group1 The blind will jog 1x Page 15 of 23 version: 1.0...
  • Page 16 MANUAL 6.2.3 Release the manual control button The motor LED turns red to acknowledge the motor is in program mode 6.2.4 Use the  open ,  stop and  close buttons to move the blind to the new bottom position. Use the  and ...
  • Page 17 MANUAL 6.2.6 Press and hold the manual control button 6.2.7 Press the  button. close The blind will move to the top limit to acknowledge the new bottom limit is set 6.2.8 Release the manual control button The motor LED turns off 6.2.9 Press and hold the ...
  • Page 18 MANUAL 6.2.10 The new bottom limit is set! 7. Additional actions 7.1. End limits reset (factory default) This procedure will erase all limits stored in the volatile motor memory. It will not clear the Network ID and Group assignments.  Note This procedure can be skipped for a fresh out of the box motor.
  • Page 19 MANUAL 7.1.1 Remove (battery) power from the motor by inserting the USB-C connector into the motor head. 7.1.2 Press and hold the on the manual control button motor. Page 19 of 23 version: 1.0...

  • Page 20: Network Reset

    MANUAL 7.1.3 Apply power to the motor by disconnecting the USB-C connector while press and hold the manual control button the motor LED turns orange after power is applied 7.1.4 Hold the manual control button until the motor jogs 1x. The end limits have been cleared and the motor will re-boot.
  • Page 21 MANUAL 7.2.1 Press and hold the on the manual control button motor for 12 seconds The blind will jog 1x at 6 seconds and a second time at 12 seconds 7.2.2 Release the after the manual control button second jog. The Network ID and Group assignments have been cleared.
  • Page 22 MANUAL Blind type: Twist® Roller Blind After reset End limits reset (factory default), see chapter Network reset on manual control button release, see chapter 7.2. Blind type: Roller blind Network reset on manual control button release, see chapter 7.2. Blind type: Twist®...

  • Page 23: Important Notice

    MANUAL Important notice Hunter Douglas Europe B.V. and its affiliates (Hunter Douglas) reserve the right to make corrections, enhancements, improvements and other changes to its products and services, and to discontinue any product or service. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.