Table of Contents Product Manual - Nomad 830G MP Troubleshooting Specifications Schematic for FlexFill Nomad with Trycock ™ Revision Log Revision Level Date Description 01/11/2016 Original manual 11/14/2018 Update cover photo and Specs, Schematics 12/28/2018 Further update on Schematics, Plumbing and Filling options...
The Nomad Series Product Manual is designed to be used in driver can control the tank pressure while filling the unit. conjunction with Nomad 830G MP. If there are any questions regarding the operation of the tank, contact Chart’s Technical Service division at 1-800-400-4683.
Preface Product Manual - Nomad 830G MP Terms Acronyms / Abbreviations Throughout this manual safety precautions will be designated The following acronyms / abbreviations are used throughout as follows: this manual: Argon Warning! Description of a condition that can result in personal injury or...
Safety General Warning! Use only replacement parts that are compatible with liquid Chart equipment is designed and built to the most rigid oxygen and have been cleaned standards, however no piece of mechanical equipment can for oxygen use. ever be made 100% foolproof. Strict compliance with proper safety and handling practices is necessary when using a Do not use regulators, fittings, hoses, etc., which have been...
Safety Product Manual - Nomad 830G MP The remainder of this safety bulletin addresses those adverse Most individuals working in or around oxygen deficient environments that may be encountered when a cryogenic atmospheres rely on the “buddy system” for protection - container has been severely damaged.
Product Manual - Nomad 830G MP Safety Compatibility involves both combustibility and ease of Nitrogen and argon vapors in air dilute the concentration ignition. Materials that burn in air may burn violently in pure of oxygen necessary to support or sustain life. Inhalation...
Product Manual - Nomad 830G MP Introduction/Operation General Initial Inspection The new Nomad 830 MP Storage and Delivery System is Upon receipt of a Nomad 830 MP, inspect for the following: another extension of the Perma-Cyl MicroBulk Storage ® • Any shipping damage to the cylinder, trailer or vaporizer, System's innovative design and technology.
Introduction/Operation Product Manual - Nomad 830G MP Preparing the Tank for Use Close valves on the final line regulator or 6-port manifold (Refer to Figure 3) Ensure pressure has been relieved from all equipment Disconnect the trailer from the tow vehicle and use the lines.
Product Manual - Nomad 830G MP Introduction/Operation PB Gauge "D" Economizer "C" Road Relief "A" Vent "F" Gas Use "E" Pressure Building "B" Pressure Building Figure 3 - Major Plumbing Components "B" adjusting the PB regulator (R-1). Standard PB set point for Caution! If liquid can be trapped in the the Nomad is 185 psig.
THE MATERIALS AND INFORMATION, INCLUDING TH OF DESIGN PRESENTED BY THIS PRINT, IS THE EXC Connect the proper regulator/regulating manifold to the PROPERTY OF CHART INC., AND IS CONFIDENTIAL IN will begin flowing through the external ACCORDINGLY, THIS INFORMATION IS SUBMITTED T...
Product Manual - Nomad 830G MP Introduction/Operation The operator should review the safety precautions found in the Safety section before conducting a gas or liquid Pressure Gauge withdrawal operation. Protective eyeglasses and gloves should always be worn Four-Way Valve At low continuous flow rates, the Nomad tank is capable of delivering warm gas through the line regulator.
Product Manual - Nomad 830G MP Filling Procedure First Fill/Purge Procedure Fill Nomad tank with 5000 standard cubic feet of product. Primarily use the bottom fill on a FlexFill style tank. Make sure some product is also routed through Note: The Nomad tank is shipped with NF purity the top fill lines to purge them prior to totally filling the nitrogen gas.
Optional Equipment Chart’s Nomad 830 mobile MicroBulk system can be ordered with a variety of option kits that make it a truly versatile product...
Page 19
Product Manual - Nomad 830G MP Filling Procedure Connect or place the other end of the hose onto the inlet The pressure building valve can be opened to build of the cryogenic equipment that will receive liquid. and maintain a higher cylinder pressure during liquid...
Page 25
Product Manual - Nomad 830G MP Troubleshooting The following table is arranged in a Trouble/Probable Cause/Remedy format. The probable causes for specific problems are listed in descending order of significance. That is, check out the first cause listed before proceeding to the next.
Page 26
Troubleshooting Product Manual - Nomad 830G MP Trouble Probable Cause Remedy Ice on external Weak vacuum or failed vacuum. 1. Check if tank pressure is routinely high even during vaporizers and/or gas use and / or if tank has cold or ice spots even plumbing when not in operation as sign of vacuum problem.
Page 27
Product Manual - Nomad 830G MP Troubleshooting Trouble Probable Cause Remedy Gas supply to Gas withdrawal rate from Nomad tank 1. Reduce gas withdrawal rate to within specified gas-use equipment exceeds the capacity of tank’s ambient parameters. is too cold.
Page 28
2. Cover pump-out port to keep moisture from getting into the annular space. 3. Call gas service technician to replace and repair tank. Warning! Use only parts which are cleaned and approved for oxygen service. Chart recommends the use of only Chart approved parts.