Summary of Contents for Flamerite Fires Glazer 600
Page 1
Installation, Precautions & Servicing Glazer 600 900 1000 1500 1800 Luca 450 1500 IMPORTANT Carefully remove the fire from the packing checking neither the heater nor the power cable has been damaged during transport. Do not operate the fire if damaged. Please bear in mind the weight of the fire before removal from the packaging and installation.
Important Safety Information and Warnings • WARNING: In order to avoid overheating, do not cover the heater. • For indoor use only. • Do not use the fire in the vicinity of a bath, shower or swimming pool. • Never use the fire to dry laundry. •...
RECYCLING Please recycle responsibly. Take your item to your local recycling centre. You can easily locate your nearest centre on the www.recyclenow.com website or check with your retailer for details on either a collection service or a store take-back scheme (some may apply charges).
Installation Instructions DO NOT TWIST, FORCE OR SQUEEZE THE FIRE DURING THE INSTALLATION PROCESS. There must be enough clearance for the fire to comfortably fit inside or against a wall. DO NOT SQUEEZE INTO AN OPENING as this may deform the case and stop the glass from moving correctly. The height at which you may wish to fix the fire in or on the wall is up to you, we recommend anywhere from 350-450mm from the floor to the bottom of the fire opening (not the bottom of the fire).
Page 5
1. Luca 450 freestanding (with or with out log box) Move and position to your required location and go to Fuel Effects in the next section. If fitting the optional flue pipe, this is simply placed onto top and against the wall. 2.
Page 6
Remove the M6 bolts and washers (remove the bottom bracket only). Mark up and drill the holes with an M10 bit and fit the rawl plugs. Using the 60mm screws, secure the bracket to the wall. b. Top Bracket Fixings 1000 1500 1800...
Page 7
Place and hold the fire on the bottom bracket and screw the top bracket back onto the fire with the 13mm self-tappers. At this point you will be able to level the fire accordingly when refitting the M6 bolts and washers through the slots of the bottom bracket and back into the fire.
Page 8
c. Using four of the 13mm screws secure the base to the fire along the side flange and fit the décor trim B. The décor trim is the long black channel that provides a neat edge along the bottom of the fire opening, it is held in place with magnets.
Page 9
Slide the top from the front D between the flange running around the opening and the pull-out tabs. Make sure the top of each gloss black decorative panel C fits into the recess around the cut out as the top pushes back towards the wall. On the underside using four of the 13mm self-tappers provided, secure the sides of the top only.
Page 10
5. Luca top and base, remove and replace. (Illustrations in this instance show the 450, the sme priceipal should be applied to the 1500) • Remove the four screws and slide the top forward. • Remove the two side and front dresser rails, they are held on with magnets. •...
Page 11
Fuel Effects The fuel effects must be positioned as in the images below. Care must be taken to ensure the channel at the front of the fire is not obstructed. Anything dropped into it, must be removed before installing the front glass panel. Visit www.flameritefires.com/product-support/instructions-fuel-effects.html if you require clearer...
Page 14
1500 & 1800 red line in the first image, is the centre of the fire. Leave approximately 150mm either end of logs 15 & 18 to allow the 1800 logs 19 to 25 to be fitted at either end. 14 | P a g e...
Page 16
Glass Fitting & Removal We recommend two persons to fit the Glazer 1500 & 1800 glass Push the side glass back towards the rear of the case A You will notice there is a long gap on the underside of the opening 10mm in width that runs along and in front of the heater grills.
Installation). Remove the two screws from either side of the fuel bed and lift out of place. Remove and replace the lamps, fuel bed, fuel effect and glass. Please note that replacement lamps are covered by a 2-year warranty. Replacements are available from Flamerite Fires Ltd Replacing...
With distance control option Room temperature control, with open window detection Adaptive Start With electronic room temperature control plus week timer Contact details: Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs. WS13 7AU Nitra Flame Model identifier (s) 1000 1500 1800...
Need help?
Do you have a question about the Glazer 600 and is the answer not in the manual?
Questions and answers