Hide thumbs Also See for OnmiGlide 1300:

Advertisement

Quick Links

Carefully remove the fire from the packing, checking that neither the heater nor the power cable has been damaged during transport. Do not
operate the fire if either is damaged. Please bear in mind the weight of the fire before removal from the packaging and installation. Consider if
help is required. Any alteration to the power cable should only be done by a qualified electrician and to the Flamerite Fires guidelines stated
below. Your fire is guaranteed for one year from the date of purchase. In the unlikely event of a breakdown you have access to our customer
services team, simply call 01543 251122 during office hours, 9am – 5pm or e-mail on
that is packed at the side of the fire.
INSTALLATION
Where a chimney is not blocked off completely it will cause the heater to cut out during use. ONLY if installing into a chimney and you are not
sure that you have cut off the draw 100% we recommend covering the slots in the rear and at either side.
Automatic safety cut out: The heater is fitted with an automatic cut out to prevent any damage due to overheating. The element will continually
and automatically cut out if the airflow is obstructed. Never cover the air outlets. To reset, switch the fire off, disconnect from the mains supply,
remove the cause of the overheating, check the micro switches and allow to cool for a suitable period then switch the fire back on. Caution: In
order to avoid a hazard due to inadvertent resetting of the thermal cut out, the appliance must not be supplied through an external switching
device, such as a timer, or connected to circuit regularly switched on and off by a utility.
Electrical connections: Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement fuses must be 13A and ASTA
approved. If the fuse cover is lost the plug must not be used until a replacement cover, of the same colour, is obtained from an electrical retailer.
The appliance is fitted with a moulded plug if it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse
removed. Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as this could cause a hazard. If
the mains cable is damaged it must be replaced by the manufacturer or an authorised technical service centre.

WARNING THIS APPLIANCE MUST BE EARTHED

As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in your plug proceed as follows: -
The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E, or
coloured green or coloured green and yellow, or marked with the earth symbol
The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N, or coloured
black.
The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L, or coloured
red.
Insert the plug tightly into its IEC connector underneath the fire if not already done so. If the removal of the plug is absolutely necessary for
installation, cut off in an area within 100mm only of the plug itself. Any further will affect your warranty.
This product is only suitable for well insulated spaces or occasional use
Installation & Precautions
The wires in the mains lead are coloured in accordance with the following code.
Green and yellow:
Blue:
Red:
Instructions 1300
info@flameritefires.com
IMPORTANT
EARTH
NEUTRAL
LIVE
Page 1 of 3
The accessories are found in a box

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OnmiGlide 1300 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Flamerite Fires OnmiGlide 1300

  • Page 1 Please bear in mind the weight of the fire before removal from the packaging and installation. Consider if help is required. Any alteration to the power cable should only be done by a qualified electrician and to the Flamerite Fires guidelines stated below.
  • Page 2 The Fire Front: is held on by four keyhole slot brackets, the corresponding screws are attached to the case. Lift the front to remove or replace it back onto the fire. Fig.1 Fig.1 Using in a Fireplace Suite: Place into the suite from the front. Secure using the 4 x 12mm screws provided, one at each counter sunk hole in the flange corners. Using as a Hole in the Wall: The inset dimensions for Hole in the Wall: depth 16cm, height 50cm and width 132cm.
  • Page 3 MAINTENANCE Before any maintenance/cleaning is undertaken, always disconnect the fire from the mains power supply. Replacing Lamps (Dimmable 240V 7W 3000k E14 LED lamps): Replacements are available from Flamerite Fires info@flameritefires.com Allow a suitable time for the lamps to cool then remove the glass & fuel effect (see Installation). Remove the two screws from either side of the fuel bed and lift out of place.

This manual is also suitable for:

Solace 400Ennio 400Raylia 400Omniglide 600Odyssey 600Omniglide 900

Table of Contents