Download
Share
Print this page
PEERLESS A100WALLARM2 Installation And Assembly Manual
  1. Manuals
  2. Brands
  3. PEERLESS Manuals
  4. Projector Accessories
  5. A100WALLARM2
  6. Installation and assembly manual

PEERLESS A100WALLARM2 Installation And Assembly Manual

Hitachi projector short throw wall arm
Hide thumbs

Advertisement

Quick Links

Download this manual
Installation and Assembly:
HITACHI PROJECTOR SHORT THROW WALL ARM
Model: A100WALLARM2
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
This product is intended for use with UL
Listed products and must be installed by a
R
qualified professional installer.
Maximum UL Load
Capacity: 40 lb (18 kg)
ISSUED: 08-17-09 SHEET #: 090-9186-4 02-09-10

Advertisement

loading
Need help?

Need help?

Do you have a question about the A100WALLARM2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for PEERLESS A100WALLARM2

Summary of Contents for PEERLESS A100WALLARM2

  • Page 1 Installation and Assembly: HITACHI PROJECTOR SHORT THROW WALL ARM Model: A100WALLARM2 This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Maximum UL Load Capacity: 40 lb (18 kg) 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com...

  • Page 2: Table Of Contents

    WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

  • Page 3: Parts List

    N M5 x 12 mm security washer head screw 510-1064 O 4 mm allen wrench 560-9646 wall template for A100WALLARM2 (not shown) LIT-0406 Some parts may appear slightly different than illustrated. 3 of 11 ISSUED: 08-17-09 SHEET #: 090-9186-4 02-09-10...

  • Page 4: Mount Position And Throw Distance

    Mount Position and Throw Distance NOTE: Use charts (see fig 1.1 or fig 1.2) below to determine the placement of projector in relation to mounting location of wall arm and white board. Chart numbers will have a ±8% discrepancy due to the optics of the projector. THROW DISTANCE: (The distance from projector edge to screen surface) CENTER OF...

  • Page 5: Option 1 - Installation To Single Wood Stud Wall

    Option 1 - Installation to Single Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

  • Page 6: Option 2 - Installation To Solid Concrete And Cinder Block Wall

    WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1"...

  • Page 7: Attaching Wall Arm Assembly And Adapter Plate

    Remove knobs and 1/4" washers from top of adapter Place upper adapter plate onto edge of table and plate assembly (D). hook M5 x 12 mm screws on wall arm assembly (B) into keyhole slots on upper adapter plate. NOTE: Screws may need to be loosened if unable to slide on.

  • Page 8: Attaching Projector To Adapter Plate

    Run cords through wall arm (B) and down Attach lower adapter plate (E) to projector using four through wall bracket (A). Attach wall arm M6 x 16 mm socket pin security screws (I), and .25" assembly (B) to wall bracket (A) using two ID x .5"...

  • Page 9: Adjusting The Projector

    Secure upper adapter plate to lower adapter plate 12-1 Adjust mount to desired mount position using chart using two M5 x 25 mm washer head security on page 3 fig. 1.1. Once mount position is screws (J). determined tighten all M5 x 12 mm screws as Use security wrench (O) to fasten all screws.
  • Page 10 Roll Adjustment Loosen knobs on left side of projector, and tighten knobs on right side of projector to roll projector to the right. Reverse for projector roll to the left. LOOSEN DO NOT TIGHTEN ADJUST SUPPORTING SURFACE NOT SHOWN FOR CLARITY Pitch Adjustment Loosen knobs on front of projector, and tighten knobs on back of projector to pitch projector forward.
  • Page 11 11 of 11 ISSUED: 08-17-09 SHEET #: 090-9186-4 02-09-10 © 2009 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.