Subscribe to Our Youtube Channel
Related Manuals for TriMark e-ASK UM27
Summary of Contents for TriMark e-ASK UM27
- Page 1 e-ASK lectronic ccess ecurity eyless-entry CAN Multiplex System CAN Multiplex System Installation & Instructions (UM27 ~ 24324-03)
-
Page 2: Table Of Contents
Table of Contents Introduction .................. 1 e-PAD Operation and Features ........... 1 Locking Doors With Keypad ............1 Unlocking Doors With Keypad ........... 1 e-FOB Operation and Features ..........2 Additional Features ..............2 Dome/Porch Light Activation ............. 2 e-PAD Anti-tamper Deactivating Feature ........2 Teaching Keypad New Authority/Access Codes ...... -
Page 3: Introduction
Introduction This manual provides the necessary information for the proper installation and use of TriMark’s CAN e-ASK system. The e-ASK system comes with the following components: e-FOB keyless entry radio frequency [RF] FOB transmitter and receiver e-PAD keypad user interface e-PAD Operation and Features The e-PAD is shipped with default authority and access codes. -
Page 4: E-Fob Operation And Features
e-FOB Operation and Features Button Function Lock Locks all doors Unlock Unlocks all doors Note: The RF features are an option that may not be available on your vehicle. The CAN module and transmitters are shipped programmed. After making all necessary wiring connections, (see page 6 for wiring information), the e-FOB system will function as shown. -
Page 5: Assign New Access Codes
Notes: The authority code is to be controlled by individuals (owners of vehicle, fleet manager, etc.) who manage the distribution of access codes to vehicle users. The authority code should be changed when the vehicle is sold. The authority code does not enable secure functions (lock/ unlock doors, etc.). -
Page 6: Teaching Additional Transmitter Fobs
The following area can be used to document the access code assignments. Access code: Access # Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Teaching Additional Transmitter FOBs This applies only to the e-ASK system that includes the RF receiver door module. -
Page 7: E-Ask Can Dip Switch Configuration
Option 2 (if no CAN keypad is connected to network) 1. Remove power from door module. 2. Open up door module enclosure. 3. Move DIP switches 4-6 to the “ON” position. 4. Connect door module to CAN network. 5. Connect power to door module. 6. - Page 8 DIP Switches 4-6: The setting of DIP switches 4-6 define configuration of the I/O RF receiver module. Different configurations provide different functionality for keypad and interior switches. The following configuration allows for door lock and window control: DIP Switch 4: Off DIP Switch 5: Off DIP Switch 6: Off DIP Switch 7:...
-
Page 9: Wiring Assignments
Wiring Assignments Gray Left Header Connector: Deutsch DT06-12SA (currently 128A) Terminal: Deutsch 1062-16-1122 Wedgelock: W12S (currently 128) Dome Light output Antennae pin CAN Low Door Lock output CAN High Ground Door Lock input Window UP Window Down Door Unlock input 8 Door Unlock Power input... -
Page 10: Troubleshooting
Troubleshooting Problem Description Possible Solution e-FOB Hints Verify power to the I/O module and RF receiver. Button press does not provide correct operation Re-teach the FOB transmitter to the receiver. Mount RF receiver away from enclosed metal areas and fully extend antennae. No operation or intermittent Check FOB transmitter battery voltage. - Page 11 Problem Description Possible Solution e-ASK I/O Module Hints Verify power to the I/O module. No response in any system element. No LED flash (LED is under enclosure cover). Verify DIP switches are set to correct Unexpected operations occurs configuration setting. I/O module is detecting problem with communication network (CAN).
- Page 12 UM27 24324-03 09/11-2...
Need help?
Do you have a question about the e-ASK UM27 and is the answer not in the manual?
Questions and answers