SIG Award Winning Model Designs Piper Cherokee Assembly Instructions Manual

SIG Award Winning Model Designs Piper Cherokee Assembly Instructions Manual

Advertisement

Your kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction.
Wood Bag:
1 LC-504-01
1 LC-504-03
1 LC-504-05
1 LC-504-07
7 Leading Edge & Fuselage
Stringers
4 Trailing Edge
2 Main Landing Gear Blocks
2 Control Surface Pushrod
Misc. Parts Loose in Box:
1 Center Section & Fuselage
Sheet
1 Plan Sheet # I
1 Decal Sheet
2 Main Landing Gear Wire
1 Molded Plastic Canopy
Hardware Bag:
2 Control Horn
1 Elevator Joiner
4 Nylon Clevis
4 Main Landing Gear Attach
Screw
Nose Landing Gear Bag:
1 Nose Gear Wire
1 Steering Collar
1 Steering Arm Fitting
4 Mounting Nuts
COMPLETE KIT PARTS LIST
3/32"x4"x24" Laser Cut Balsa Sheet
3/32"x4"x24" Laser Cut Balsa Sheet
3/32"x4"x24" Laser Cut Balsa Sheet
1/16"x3"x4 1/2" Laser Cut Birch Ply
3/32" sq.x24" Balsa Strip
1/16"x1"x24" Balsa Sheet
3/8"x1/2"x3 1/2" Grooved Hardwood
Block
1/16"x18" Wire, Threaded One End
1/16"x3"x36" Balsa Sheet
Small Nylon Control Horn
1/8" x 3" Birch Dowel
Small Nylon Clevis
#4 Sheet Metal Screw
3/32" Pre-Bent Wire
3/32" Collar
Molded Nylon Fitting
2-56 Nuts
1 LC-504-02
3/32"x4"x24" Laser Cut Balsa Sheet
1 LC-504-04
3/32"x4"x24" Laser Cut Balsa Sheet
1 LC-504-06
3/32"x4"x24" Laser Cut Balsa Sheet
6 Leading Edge and Spars
1/4" sq.x24" Balsa Strip
2 Wing Tips
3/4" Balsa Trianglex7 1/4"
2 Rudder Fairing Block
3/4"x3/4"x3 1/4" Balsa Block
1 Cowl Blocks and servo
1/4" sq.x12" Spruce
rails
2 Throttle and Nose Gear
1/16"x10" Wire, Threaded One End
Pushrod
1 Fuselage Stringer
3/32"x3/16"x36" Balsa Strip
1 Plan Sheet #2
1 Instruction Book
1 Molded Plastic Cowl
4 HornScrew
2-56 x 3/8" Machine Screw
4 Cowl Attach Screw
#2 Sheet Metal Screw
2 Wing Dowels
3/16" x 4" Dowels
1 Nose Gear Bearing
Molded Nylon Bearing Block
1 Steering Arm
2-56 x 1/2" Threaded Stud
4 Mounting Screws
2-56 x 3/8" Machine Screws

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Award Winning Model Designs Piper Cherokee and is the answer not in the manual?

Questions and answers

Summary of Contents for SIG Award Winning Model Designs Piper Cherokee

  • Page 1 Your kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction. COMPLETE KIT PARTS LIST Wood Bag: 1 LC-504-01 3/32"x4"x24" Laser Cut Balsa Sheet 1 LC-504-02 3/32"x4"x24" Laser Cut Balsa Sheet 1 LC-504-03 3/32"x4"x24"...
  • Page 3: Building The Tail Surfaces

    Note: These are parts that we have used and are familiar with. There are many other brands available and you may substitute other items that you are more comfortable with or have on hand. 1 Engine Norvel Big Mig .049 or Norvel Big 3 Hinges Sig Easy Hinges # SH-710 or Du-Bro Kwik Hinge Mig .061 #537 1 Motor Mount Dave Brown #0506 4 Motor Mount Screws and 4-40x3/4"...
  • Page 4 15. Fit parts F-13, F-14, F-15 and F-16 into position on the fuselage top. The formers should be 90 degrees to the fuselage top. Glue both parts F-17 (fuel tank supports) into position. 16. Glue the 3/32" x 3/16"" top stringer into position between formers F-14 and F-17. Now glue the 3/32" sq. stringers into position.
  • Page 5 Building the Left Wing 38. Pin the lower 1/4" sq. spar and the lower trailing edge sheet to the left wing plan. 39. Glue the lower plywood dihedral braces to the front and rear of the lower spar. Cut the lower 1/16" sheet for the lower inboard end of the wing and glue in place between the trailing edge and the dihedral brace.
  • Page 6: Final Assembly

    LIMIT OF LIABILITY: In use of our products, Sig Mfg. Co.'s only obligation shall be to replace such quantity of the product proven to be defective. User shall determine the suitability of the product for his or her intended use and shall assume all risk and liability in connection...

Table of Contents