6�16 Selecting The Interface Mode; 6�17 Locking The Unit; 6�18 Exiting A Configuration Window; Enabling Or Disabling Inputs - Monacor DRM-882LAN Instruction Manual

6.15.1 Enabling or disabling inputs

Under "External Signal Enable", select the
switching signals at the connections INPUT
PORT (13) that are to be enabled for switch-
ing over the configuration . A tick in the box
indicates that the corresponding input will be
included in the switchover procedure .
6.15.2 Selecting the logic type (high / low)
Under "Active Mode", define if the switch-
over is to be triggered by high level ["External
Input line active High" (+5 V)] or low level
["External Input line active Low" (0 V)] .

6.15.3 Selecting priorities

Under "Priority", select the priority to be used
for the switching inputs during switchover .
Click the button "?" to call up a table (fig . 39)
providing information on the actual meaning
of the number entered in the field "Configure
Priority" . For each number, the table lists, in
descending order, the priorities that are as-
signed to the individual inputs .
Example:
All inputs have been enabled for switchover . The
logic type is "active High" and the value in the field
"Configure Priority" has been set to 3, i . e ., according
to the table, the order of the inputs is S1, S4, S3,
S2 . This means:
If switching input 1 is on high level (+5 V are present
between terminal "S1" and
figuration will be retrieved (consequently, the other
inputs will be of no relevance) .
If switching input 1 is on low level (0 V are present
between terminal "S1" and
input 4 is on high level, the 4
will be retrieved .
If the switching inputs 1 and 4 are on low level and
if switching input 3 is on high level, the 3
configuration will be retrieved .
If switching inputs 1, 3 and 4 are on low level and
if switching input 2 is on high level, the 2
configuration will be retrieved .
Fig. 39 Window "Priority Info"
All rights reserved by MONACOR
No part of this instruction manual may be reproduced in any form or by any means for any commercial use.
38
6.16 Selecting the interface mode
Similar to the procedure in the system menu,
it is possible to define if one of the interfaces
USB or RS-485 is to be set manually or to be
recognized automatically by the unit .
1) In the configuration window, under
"USB/ RS 485", click the button "Setup" .
The dialog window "USB/ RS 485 Setup"
is displayed .
2) From the list field, define if the switchover
is to be performed automatically ("USB/
RS 485 Automatic") or if the USB or RS-
485 interface most recently set by means
of the system menu (
to be used ("USB/ RS 485 Manual") .
3) Click "OK" to confirm your selection or
click "Cancel" to cancel it .
6.17 Locking the unit
To protect the unit against unauthorized op-
eration, click the button "Lock Front-panel"
on the upper right of the display so that it
appears to be "pressed" . Once the connec-
tion to the computer has been disconnected
(configuration window closed [
ter 6 .18] and "Disconnect" clicked), it will
not be possible to operate the DRM-882LAN
via its buttons
To unlock, re-establish the connection to
), the 1 extra con-
st
the computer ("Connect"), call up the con-
figuration window ("Edit") and press ("disen-
gage") the button "Lock Front-panel" .
) and if switching
extra configuration 6.18 Exiting a configuration window
th
To exit a configuration window, click the but-
ton  located in the upper right corner . Then
extra
rd
confirm the confirmation message .
extra
nd
® INTERNATIONAL GmbH & Co. KG.

7 Specifications

DRM-882LAN
Frequency range: . . . . . 20 – 20 000 Hz
Audio inputs
Input voltage: . . . . . . . 6 .2 V (max .)
Impedance: . . . . . . . . 10 kΩ
Connections: . . . . . . . Screw terminals,
Phantom
power supply: . . . . . . . +48 V, switchable
Audio outputs
Output voltage: . . . . . 6 .2 V (max .)
☞ chapter 5 .3 .3) is
Impedance: . . . . . . . . 50 Ω
Connections: . . . . . . . Screw terminals,
S/ N ratio (A-weighted)
Microphone: . . . . . . . . > 98 dB
Line: . . . . . . . . . . . . . . > 104 dB
THD: . . . . . . . . . . . . . . . < 0 .005 %
A / D and D /A converters
Quantization: . . . . . . . 24 bit
Sampling rate: . . . . . . 48 kHz
☞ chap-
Signal processor
DSP type: . . . . . . . . . . SAM3716
Data format: . . . . . . . . 24 bit (data)
Switching inputs: . . . . . 0 – 5 V (TTL level)
Switching outputs: . . . . 0 – 5 V (TTL level),
Power supply: . . . . . . . . 230 V/ 50 Hz
Power consumption: . . . 20 VA (max .)
Ambient temperature: . 0 – 40 °C
Dimensions
Width: . . . . . . . . . . . . 482 mm
Height: . . . . . . . . . . . . 44 mm,
Depth: . . . . . . . . . . . . 250 mm
Weight: . . . . . . . . . . . . 2 .5 kg
DRM-882WP
Dimensions (W × H): . . . 86 × 86 mm
Mounting depth: . . . . 30 mm
Power supply: . . . . . . . . ⎓ 5 V/ 20 mA
DRM-882WPX
Dimensions (W × H): . . . 144 × 80 mm
Mounting depth: . . . . 45 mm
Power supply: . . . . . . . . ⎓ 12 V/ 75 mA
±1 dB
balanced
balanced
× 96 bit (coeffi-
cients)
150 mA (max .)
1 RS (rack space)
Subject to technical modification .