Table of Contents
Advertisement
Available languages
Available languages
DRM-882WPX
Select Routing
SET
Select Routing
Input 1
Input 8
ESC
Zone Control
SET
Zone X
Mute
Volume
ESC
Info
SET
DRM-882WPX
Lock
SET
Lock DRM-882WPX
Are you sure?
Fig. 11 DRM-882WPX – control menu "Zone Mode"
5.6.2
Operating mode "Zone"
The control menu of the operating mode
"Zone" is shown in fig . 11 . The following
options are available:
–
Select Routing
puts to the output X defined during setup
and setting of the signal mixing ratio
: input assigned
Mute = Off
: input not assigned
Mute = On
: signal part of the input for this out-
Gain
put
–
/
Zone Control
Zone
settings for output X
: muting
Mute
: volume
Volume
Step
–
: display of system information
Info
Fig. 12 Main window
28
ZONE X
SET
Mute
SET
Mute = Off
ESC
Gain
SET
Gain [dB]
G = 0
ESC
G =-30
ESC
SET
Mute = Off
On
ESC
SET
Volume [dB]
Step=1.0dB
V=+18.0
Step=0.1dB
V=-127.0
ESC
ID:01
Version: 1.0.0
ESC
SET
DRM-882WPX PANEL
System Locked
ESC
–
Lock
accidental operation
To unlock the control panel, keep the but-
tons SET and ESC pressed for more than
: assignment of the in-
5 seconds .
5.6.3
In the standby mode, the display is deactivat-
ed and the control panel is protected against
accidental operation .
X:
keep the rotary knob (23) pressed for more
than 5 seconds .
: increment
Note: An automatic change to the standby mode can
be defined during setup (
On
SET
> 5 s
+
ESC
: Locking of the control panel against
Standby mode
To call up and exit the standby mode,
☞
chapter 4 .6 .1) .
6 Remote Control via
a Computer
The computer software supplied can be used
to operate the DRM-882LAN by remote con-
trol . Thus, the unit may also be configured
for operation without a computer . The con-
figurations created may be saved on the unit
and on the computer .
Note: If the DRM-882LAN is connected to a control
panel DRM-882WP/-882WPX, make sure that the
control panel is not operated while the DRM-882LAN
is remote-controlled via a computer [e . g . lock the
control panel] . Otherwise, connection conflicts might
occur .
6.1 Installing PC Software
The installation of the control program sup-
plied requires a PC equipped with the Win-
dows XP operating system (SP2) or later,
a memory of at least 512 MB, 10 MB free
hard-disk space and a USB, Ethernet or RS-
485 interface . The screen resolution should
be at least 1024 × 768 pixels . To install the
PC software, start the installation program
SetupDRM-882LANv...EXE on the CD sup-
plied and follow the instructions of the in-
stallation program .
Windows is a registered trademark of Microsoft Corporation in
the United States and other countries.
6.1.1
Installing an interface driver
The connection via the USB interface or the
Ethernet interface requires a special driver
which is included on the CD supplied . Call up
the file USB[...]SETUP .EXE to install the driver
automatically . The driver will simulate a serial
interface for the operating software .
6.2 Starting the PC software
Start the control program DRM-882LAN
V...EXE on the PC . The main window (fig . 12)
appears, showing the units that were most
recently connected . For each unit, a separate
window is provided: the header shows infor-
mation with regard to the interface as well as
the connection status .
6.2.1
Adding units
To add a(nother) unit, click the button "Add
Device" .
If USB is selected as the current interface type
(the text on the button on the upper left is
"USB-COMx"), the following unit window
will be displayed:
Fig. 13 USB unit window
After that, it is not possible to add further
units .
If RS-485 is selected as the current interface
type (the text on the button on the upper
left is "RS485-COMx"), the following dialog
window will initially be displayed:
Advertisement
Chapters
Table of Contents
