Related Manuals for HunterDouglas Reveal
Summary of Contents for HunterDouglas Reveal
- Page 1 Installation Operation Care • • Aluminum Blinds MagnaView Tilt Feature ® 8802480016F 4/20...
-
Page 2: Table Of Contents
CONTENTS GETTING STARTED Product View — Reveal with MagnaView ..............1 ® ® Product View — Natural Elements with MagnaView ............2 ® Tools and Fasteners Needed ....................3 Unpack the Blind ........................3 INSTALLATION Installation Overview ......................4 Mount the Installation Brackets — Inside or Ceiling Mount ..........5 Mount the Installation Brackets —... -
Page 3: Getting Started
GETTING STARTED Product View — Reveal with MagnaView ® ® Bracket Shim End Bracket (Optional) 2" or 4" Extension Spacer Block Brackets (Optional) (Optional) Bracket Intermediate Bracket Intermediate Decorative (If Required) Bracket Valance Spacer Block (Optional) End Bracket Spacer Block... -
Page 4: Product View - Natural Elements ® With Magnaview
GETTING STARTED Product View — Natural Elements with MagnaView ® ® Bracket Shim Bracket 2" or 4" Extension (Optional) Brackets (Optional) End Bracket Spacer Block (Optional) Artemis Intermediate ™ Valance Bracket Intermediate (If Required) Bracket Spacer Block (Optional) Headrail End Bracket Spacer Block (Optional) Bracket... -
Page 5: Tools And Fasteners Needed
GETTING STARTED Thank you for purchasing Hunter Douglas horizontal blinds. With proper installation, operation, and care, your new blinds will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. Tools and Fasteners Needed Ballpoint pen ■... -
Page 6: Installation
Installation Overview Two end brackets are used to mount horizontal blinds. ■ Wider blinds also require one or two intermediate brackets, as shown in the tables below. Intermediate Bracket Bracket Reveal with MagnaView ® ® Natural Elements with MagnaView ® Intermediate... -
Page 7: Mount The Installation Brackets - Inside Or Ceiling Mount
INSTALLATION Mount the Installation Brackets — Inside or Ceiling Mount Bracket Shims (Optional) Bracket shims are used to gain clearance for valance One Shim Folded Over clips with inside or ceiling mounts. One shim for each end bracket and two shims for each intermediate bracket Intermed are included. -
Page 8: Mount The Installation Brackets - Outside Mount
INSTALLATION Use a ⁄ " drill bit to drill holes for the mounting screws. ■ Attach the end brackets using the screws provided. ■ IMPORTANT: The front edges of the end brackets must align. Attach the Intermediate Brackets (If Required) Evenly space the intermediate bracket(s) between the two end brackets. - Page 9 INSTALLATION Attach the End Brackets Align the outside edge of each end bracket with the outer marks and mark diagonal screw ■ holes. Use a ⁄ " drill bit to drill holes for the mounting screws. ➤ Attach the end brackets using two screws through diagonal holes. ■...
- Page 10 INSTALLATION Extension Brackets (Optional) Attach 2" or 4" extension brackets to the mounting surface in the same locations where the end brackets and intermediate brackets would be attached. Use the provided screws to mount each extension bracket. ■ IMPORTANT: The tops of the end brackets and intermediate bracket(s) must align. Attach the installation brackets to the extension brackets using the screws and nuts ■...
-
Page 11: Install The Blind
INSTALLATION Install the Blind Adding Projection to the Valance The magnetic valance clips have a projection adjustment feature. By pulling the clips outward, the clips can provide an additional ⁄ " projection. The clips offer two projection positions. When the clips are fully compressed, the narrowest projection is ⁄... - Page 12 INSTALLATION Attach the Magnetic Valance Clips to the Valance Lay the valance face down on a protected ■ surface with the back side up. Insert the clip dovetail into the valance ■ groove. Twist the clip until it is straight with the ■...
- Page 13 INSTALLATION Attach the Universal Valance Clips to the Headrail With fully recessed inside or ceiling mounts, the universal valance clips must be installed before mounting the headrail. Attach clips 3" to 6" from each end of the headrail. Avoid any internal components. ■...
- Page 14 INSTALLATION Attach the Valance Splice (If Required) For valances that are spliced, join the two mitered valance pieces together by sliding the valance splice clip over the back of the valance where the two halves meet. Miters Valance Splice Clip Mount the Headrail Tilt the headrail so that its back lip slides under the front lip of the end brackets and ■...
-
Page 15: Complete The Installation
INSTALLATION Adjust the Headrail Tightness If the headrail is loose in the end brackets, bend ■ the tabs on the end brackets outward. NOTE: The tabs may also be bent inward if the headrail is difficult to install into the end brackets. Close the End Brackets Push the cover down until it snaps over the locking ■... - Page 16 INSTALLATION Attach the Wand (If Ordered) If the blind was ordered with a wand tilter, attach the wand to the metal shaft. NOTE: Wands may appear different from the illustration, but assembly is the same. Pull the plastic sleeve from the top of the wand and insert it over the metal shaft. ■...
- Page 17 To remove the valance, gently pull the valance downward to release it from the top of the ■ clips. Rotate the top of the valance toward you. Lift up the valance to release it from the Reveal with MagnaView Decorative Valances ®...
-
Page 18: Operate The Blind
INSTALLATION Operate the Blind Tilting the Slats After installation, tilt the slats from fully closed in one direction to fully closed in the other. Repeat three or four times to calibrate the tilt mechanism to ensure proper stacking. Wand tilt (not shown): Rotate the wand to tilt the slats to ■... -
Page 19: Troubleshooting
OPERATION Troubleshooting If your blind is not operating correctly: First review the guide that came with your control device. ■ Refer to the following troubleshooting procedures for specific solutions for your blind. ■ If questions remain, please contact Hunter Douglas Consumer Support at 1-888-501-8364. Problem The blind will not fit into the installation brackets. - Page 20 OPERATION Problem When hanging, the slat pack appears to be skewed toward the cordlock side of the unit, particularly in an inside mount installation. Solution Slide the headrail in the end brackets in the opposite direction of the skew and adjust the tabs in the end brackets to maintain the position of the unit. This will center the slat pack in the window.
-
Page 21: Care
CARE Removing the Blind (If Necessary) Fully raise the blind. ■ To remove the valance with magnetic valance clips, see page 15. ■ To remove the valance with universal valance clips, see page 16. ■ Push up on the bottom of the end bracket to release the locking tab, see page 13. ■... -
Page 22: Child Safety
CHILD SAFETY WARNING For more safety information, call 1-800-997-2389. Window Blind Cord Can STRANGLE Your Child. ■ Children can climb furniture to reach cords. Move crib and furniture away. ■ Keep all cords out of children’s reach. ■ Cord Connector This component acts as a stopper to prevent inner cords from being ■... -
Page 23: Cord Cleats
CHILD SAFETY Cord Cleats Hunter Douglas offers cord cleats and we recommend their use. Attach two cord cleats 6" to 12" apart at a height where they will be out of ■ the reach of children. Take into account that a child may stand on furniture attempting to reach the cords. - Page 24 If you are not thoroughly satisfied, simply contact Hunter Douglas at (888) 501-8364 or visit hunterdouglas.com. In support of this policy of consumer satisfaction, we offer our Lifetime Limited Warranty as described below.