Manual setti ng
N/A
mode
WARNING! When kneading heavy masses,
yeast dough, do not exceed 4 minutes. An
excessively loaded device may overheat over
which will be signaled by error E1 or E4. In the
event of overheati ng, switch off the device
and allow it to cool completely before re-use.
USING THE APPLIANCE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
The descripti ons below present a general usage
patt ern only. For detailed descripti ons of specifi c
dishes, ingredients, proporti ons and weights,
refer to the cookbook.
MIXING AND COOKING
1. Install the cutt er assembly ⑦ in the jug ④.
Depending on the food processing tech-
nology, you may also need to install cutt er
guard (mixing paddle) ⑬ or the mixing
att achment (butt erfl y whisk) ⑭ or the
basket ⑮.
CAUTION! The blades are very sharp. Handle
with care.
2. Install the jug ④ in the jug slot ⑱.
3. Insert the food you want to process into
the jug. Do not exceed the maximum vol-
ume indicated on the jug with the horizon-
tal line (the top line: max. 2000 ml). If you
are going to use the basket ⑮, pour enough
water (broth, bouillon) into the jug that it
mixing, grinding,
"Pulse" functi on acti ve only
chopping,
before change temperature,
blending,
manual setti ng mode requires
shredding
declaring the mixing speed
(minimum 1 or higher)
WARNING! When choosing a high mixing
speed (from 8 to 12), the set mixing ti me
should not exceed 5 minutes.
covers the food in the basket. The scale
functi on enables precision measuring of the
ingredients you add to the jug (see: "SCALE
FUNCTION").
CAUTION! Do not fi ll the jug over its
maximum volume: 2000 ml (see the MAX
mark inside the jug). With liquids, do not go
over 1500 ml (see the
mark inside the jug).
CAUTION! Take extra care while cooking
food. Do not start the appliance if the jug
is empty. Make sure there is enough water
in the jug while cooking food in the basket.
CAUTION! While putti ng and pouring ingre-
dients into the jug be careful not to spill them
over the base of the appliance. There is an
electrical shock hazard.
4. Install the jug cover ⑧ onto the jug ④.
5. Install the measuring cup/cover cap ⑨
in the jug cover ⑧.
6. Connect the appliance to the mains and
turn it on using the on switch ⑯ on the
right side of the appliance. The appliance
will turn down if you do not take any acti on
within 5 minutes. To turn it on again press
any butt on on the control panel.
CAUTION! Further operati on of the control
panel is possible only if the jug ④ and jug
cover ⑧ have been properly installed in the
appliance. Improper installati on of the jug or
jug cover will be indicated by displaying the
"E2" or "E3" error in the middle secti on of the
display
.
A3
7. Start the mixing/kneading (Dough) or
cooking (Heati ng) programme using the
butt on
or
. Programme start will be
2H
2I
indicated by the control light next to the
corresponding butt on and the light next to
the "Start/Stop" butt on
. The left side of
2G
the display
shows the current tempera-
A1
ture in the jug, and the right side
a ti mer counti ng down 2 minutes (for the
shows
A2
2 7
Need help?
Do you have a question about the Masterchef Line Executive PSC-10 and is the answer not in the manual?