Related Manuals for Raven Case SPX 3150
Summary of Contents for Raven Case SPX 3150
- Page 1 Case SPX 3150/3185/3200 Sprayer with Raven SCS 460 Console AccuBoom™ Installation Manual P/N 016-0171-081 Rev B 01-16 Copyright 2009, 2016...
-
Page 3: Components Needed
CHAPTER INTRODUCTION ____________________________________________________________ Congratulations on your purchase of the Raven AccuBoom system! This system is designed to provide worry free turn on and turn off of your booms with respect to the as-applied coverage map. The following instructions are designed to assist you in the proper installation of the AccuBoom system. - Page 4 Manual #016-0171-081 Rev. B 07/08 Notes:...
-
Page 5: Installation
Manual #016-0171-081 Rev. B 07/08 CHAPTER INSTALLATION ___________________________________________________________ Use the following procedure to properly install the AccuBoom system on a CASE SPX3150/3185/3200 sprayer. 1. Open the access door located on the left side of the cab. 2. Locate the boom control cable located toward the rear of the cable compartment. - Page 6 Manual #016-0171-081 Rev. B 07/08 3. Disconnect the 6 pin boom connections. Important! There may be two sets of 6 pin connectors. Be sure you have located the connectors coming from the boom switches. 4. Plug the mating connectors from the CAN AccuBoom cable P/N 115- 1001-011 to the corresponding connectors previously disconnected.
- Page 7 Manual #016-0171-081 Rev. B 07-08 5. Mount the CAN AccuBoom node in a suitable located in the cable compartment. 6. Connect the AccuBoom cable to the AccuBoom node. a. Connect the rectangular connectors from the AccuBoom Cable P/N 115-1001-011 to the CAN Accuboom Node P/N 063-0172-316. Node Connection 7.
- Page 8 Manual #016-0171-081 Rev. B 07/08...
- Page 9 Manual #016-0171-081 Rev. B 07/08 9. Connect a CAN terminator P/N 063-0172-369 to the end of the CAN cable P/N 115-0171-362. Note: If the machine already has a CAN system installed, remove the terminator from the existing CAN system and move it to the CAN cable previously installed.
- Page 10 Manual #016-0171-081 Rev. B 07/08 Notes:...
- Page 11 CAN INSTALLATION ________________________________________________________________________ If the machine you are working on does not currently have a Raven CAN system, you will need a Kit, CANbus, Terminators & Power Adapter “T” P/N 117-0159-923. This kit contains the CAN Cable Adapter Tee With Power P/N 115-0171-368 and two(2) CANBus Terminators P/N 063- 0172-369.
- Page 12 Manual #016-0171-081 Rev. B 07/08 2. Connect the CAN bus to the Controller. a. Connect CAN Terminator P/N 063-0172-369 to one connector on the Can Cable Adapter Tee With Power P/N 115-0171-368. CAN Terminator b. Connect the second connector on the CAN Cable Adapter Tee With Power P/N 115-0171-368 to the CAN connector on the Envizio or Viper interface cable.
-
Page 13: System Troubleshooting
Manual #016-0171-081 Rev. B 07/08 CHAPTER SYSTEM TROUBLESHOOTING ________________________________________________________________________ The CAN AccuBoom Node P/N 063-0172-316 has additional features to allow the user to diagnose the AccuBoom system. The CAN AccuBoom node has a plastic window in the case that allows the user to view green diagnostic lights. - Page 14 Manual #016-0171-081 Rev. B 07/08 Notes:...
- Page 15 How Can I Get Service? Bring the defective part and proof of purchase to your Raven Dealer. If your Dealer agrees with the warranty claim, the Dealer will send the part and proof of purchase to their distributor or to Raven Industries for final approval.