Related Manuals for Ropox 4SingleManual
Summary of Contents for Ropox 4SingleManual
- Page 1 4SingleManual User Manual Mounting Instructions Keep this folder with product at all times! PDF 6005 / 17.09.2019...
-
Page 2: Table Of Contents
Contents INTRODUCTION ............................3 APPLICATION ............................3 TECHNICAL DATA ........................... 4 SCHEMATIC DIAGRAM OF FRAME ..................... 5 SCHEMATIC DIAGRAM OF FRAME ..................... 5 GEARBOX 96000656 2..........................6 MOUNTING INSTRUCTIONS, ILLUSTRATIONS ................. 6 MOUNTING INSTRUCTIONS, ILLUSTRATIONS ................. 7 Assembly of frame ..........................7 LIST OF COMPONENTS ........................... -
Page 3: Introduction
Introduction 4Single is a multi-function table, which may be adjusted to suit seated or standing activities. Owing to the unique design there are a variety of applications and the table is therefore also ideal for wheelchair users. This document must ALWAYS accompany the product and be read by and available to users. All users must follow these instructions. -
Page 4: Technical Data
Blue chromate, powder coating: Standard CWS 81283 RAL 7021 mat Max. load of frame: 150kg evenly distributed Temperature: 5-45° C Air humidity: 5-85% (non-condensing) Complaints: See page 12 Producer: Ropox A/S, DK-4700 Naestved, Tel.: +45 55 75 05 00 E-mail: info@ropox.dk - www.ropox.com Page 4... -
Page 5: Schematic Diagram Of Frame
Schematic diagram of frame All connections to the table must be flexible to ensure that the table moves freely within the range of adjustment. Width – 18cm 33,6cm Length – 9cm 20cm 20cm For table top length 60 - 300cm (Length of frame always 0.4 cm less than the table top, i.e. -
Page 6: Gearbox 96000656 2
Component Item No. Pcs. Gearbox 96000656 Shaft adapter, outside Hex7, inside Hex6 30*12999-047 Side fascia shaft, Hex6. Length = frame width – 13.8cm Gearbox for crank handle, Fixture & Bushing 30*12999-148 Front fascia shaft, Hex7. Length = frame length – 16.7cm Leg 1 Leg 2 Handle... -
Page 7: Mounting Instructions, Illustrations
Mounting instructions, illustrations Mounting must always be carried out by competent personnel. Prior to mounting, check that all parts have been provided. See list of components, section 6. Assembly of frame 6.1.1 Check that the height (L) of all four legs is 6.1.2 At the opposite end of the handle fit a identical. -
Page 8: List Of Components
List of components Set of legs H1, 50-41110: 1 set Set of legs H2, 50-41210: 1 set Front fascias for L=xxx cm, 50-42xxx: 1 sets Shaft Hex7 (fascia length – approx. 5cm) 1 pc. Side fascias for W=xxx cm, 50-44xxx: 1 set Shaft Hex6 (fascia width + ca.2.5cm) 1 pc. -
Page 9: Safety In Use
Check that the table moves freely from bottom to top position. After each inspection, fill in the service schedule. Only use Ropox original spare parts for replacement of parts. If other spare parts are used, the right to complain may become void. -
Page 10: Service Schedule, Operation And Maintenance
Service schedule, operation and maintenance Service and maintenance Serial No. Service and maintenance Serial No. Date: Date: Signature: Signature: Remarks: Remarks: Service and maintenance Serial No. Service and maintenance Serial No. Date: Date: Signature: Signature: Remarks: Remarks: Service and maintenance Serial No. Service and maintenance Serial No. -
Page 11: Ce-Marking
CE- Declaration of conformity The undersigned hereby declares that the following products: Product: 4SingleManual Product numbers: Set of legs, Manual Height 55-85 cm H1 50-41110 Height 65-95 cm H2 50-41210 Front fascias for frame L = xxx cm 50-42xxx From 60-300cm in increments of 1cm... -
Page 12: Complaints
Complaints See General Terms of Sale and Delivery on www.ropox.com ROPOX A/S Ringstedgade 221 DK – 4700 Naestved Tel.: +45 55 75 05 00 Fax.: +45 55 75 05 50 E-mail: info@ropox.dk www.ropox.com Page 12...
Need help?
Do you have a question about the 4SingleManual and is the answer not in the manual?
Questions and answers