Download
Share
Print this page
Episode ESA-70V-2CH-IP Manual
  1. Manuals
  2. Brands
  3. Episode Manuals
  4. Amplifier
  5. ESA-70V-2CH-IP
  6. Manual

Episode ESA-70V-2CH-IP Manual

Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
ESA - 70V - 2CH - IP AMPLIFIER
OVERVIEW
The following information will guide the installer through simple set up and programming for serial control of Episode™
ESA-70V2CH-150W/300W/500W Amplifiers.
Please read the entire document before any RS-232 setup.
If you have any questions about serial control after reading this document, please contact Technical Support.
CONTACTING TECHNICAL SUPPORT
Phone:
866.838.5052 or 704.909.5229
Email:
support@episodeaudio.com
BEFORE BEGINNING
Make sure the following items are close at hand for setup:
• ESA-70V2CH-150W/300W/500W Amplifier
• Control system with serial output
• Control system documentation
• ESA-70V2CH-150W/300W/500W
• Serial cables and adapters for connection between controller and amplifier
• List of the functions to program into the control system
FIRMWARE VERSION
The information in this document applies to ESA-70V2CH-150W/300W/500W amplifier with firmware version
01.00.78.370, or higher. If the firmware version is below 01.00.78.370, please update to the latest version.
UPDATING FIRMWARE
Via GUI
1. Ensure the firmware file is saved onto a PC and follow the steps below:
2. Click on the Micro.DSP tab
3. Click "Enable HTTP Bootloader"
4. Choose the new firmware file on your PC and click "Upload"
NOTE: Some browsers do not show file upload status, in these cases, wait about 5 minutes for the upload to complete.
5. The amplifier will reboot once the new firmware is installed. Any saved settings will be retained after the firmware
has been updated
Via OvrC®
1. Log in to your OvrC account via PC or mobile application. (See instructions in the Configuration Utility for instructions
on installation and set up of OvrC).
2. Select the ESA-70V2CH-150W/300W/500W amplifier on device list.
3. Select "Update Firmware".
Installation Manual
SERIAL PROTOCOL

Advertisement

loading

Related Manuals for Episode ESA-70V-2CH-IP

Summary of Contents for Episode ESA-70V-2CH-IP

  • Page 1 SERIAL PROTOCOL ESA - 70V - 2CH - IP AMPLIFIER OVERVIEW The following information will guide the installer through simple set up and programming for serial control of Episode™ ESA-70V2CH-150W/300W/500W Amplifiers. Please read the entire document before any RS-232 setup.

  • Page 2: Rs - 232 Port Configuration

    page | 2 RS - 232 PORT CONFIGURATION The ESA-70V2CH-IP Amplifier receives control data on the “Rx” pin and transmits control data on the “Tx” pin of the screw-down terminal serial port at the back of the amplifier. The connection cable between the amplifier and the control system will need to be configured so the Rx pin on the amplifier is connected to the TX pin on the control system, and the Tx pin on the amplifier is connected to the Rx pin on the control system.

  • Page 3: Input Switch

    Sum:ALL will sum inputs 1, 2, 3 and 4 Response Example #1: Switch Line Level Audio Input 1 to Output Speaker 1. Switch_Audio=Input:Line:001,Output:Speaker:001<CR><LF> Example #2: Sum or mix inputs 1 and 2 to output Speaker 1. Switch_Audio=Input:Sum:012,Output:Speaker:001<CR><LF> © 2015 Episode® © 2015 Episode®...

  • Page 4: Output Volume

    page | 4 OUTPUT VOLUME Example #1: Adjust the volume to 50% for Speaker 1. Output_Volume= Output Speaker : <CR> <LF> Example #2: Increase the volume for Speaker 1. Output_Volume= Output Speaker : <CR> <LF> Example #3: Decrease the volume for Speaker 1. Output_Volume= Output Speaker :...
  • Page 5 Example #2: Adjust treble output in Speaker 1 to -2dB.* Output_Treble= Output Speaker : <CR> <LF> * Any number -6 to +6. Response Example #1: Decrease treble output in Speaker 1. “Output_Treble=Output:Speaker:001,-01<CR><LF>”, Example #2: Adjust treble output in Speaker 1 to -2dB. “Output_Treble=Output:Speaker:001,-02<CR><LF>” © 2015 Episode® © 2015 Episode®...
  • Page 6 page | 6 STATUS Example #1: What input is currently selected on speaker output 1? Status= Speaker : <CR> <LF> Example #2: What is system Power status? Status= Power <CR> <LF> Example #3: What is the volume setting for speaker output 1? Status= Volume Speaker :...

  • Page 7: Year Limited Warranty

    2 YEAR LIMITED WARRANTY This Episode product has a 2-Year limited warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified or disassembled.
  • Page 8 Rev: 160802-1450...