Related Manuals for Episode ECA-70VMINI-60W
Summary of Contents for Episode ECA-70VMINI-60W
- Page 1 INSTALLATION MANUAL ECA-70VMINI-60W ECA-70VMINI-60W VOLUME 12VDC IN BALANCED IN STEREO IN UNBALANCED IN SERVICE STATUS RS-232 SPEAKER OUTPUTS L+ L- GND R+ R- S GND GND Tx...
- Page 2 page | 2 CAUTION Risk of Electrical Shock! DO NOT OPEN! ATTENTION ! RISQUE DE CHOC ! ÉLECTRIQUE PAS OUVRIR ! The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
-
Page 3: Power Supply
| 3 INTRODUCTION Thank you for purchasing Episode® amplifiers. To complete installation, follow these guidelines. Visit our website for design recommendations. CONTENTS 1x ECA-70VMINI-60W Amplifier 1x Power Supply (EE-PS3-12VDC-2A) 1x Detachable 6ft IEC Power Cable 1x 3ft 18 AWG 2-Conductor Wire... -
Page 4: Volume Knob
page | 4 AMPLIFIER UNBALANCED IN VOLUME 12VDC IN BALANCED IN SERVICE RS-232 SPEAKER OUTPUTS STEREO IN STATUS L+ L- GND R+ R- S GND GND Tx 12VDC Input (Black) Connect 12VDC power from included power supply (EE-PS3-12VDC-2A). G. Balanced Input 1 Screw-down terminal accepts and secures balanced line level mono or stereo audio signals. - Page 5 Minimum of 5" or free air space above Minimum of 3" of free air space 3" 3" on each side. ECA-70VMINI-60W Minimum of 2" of depth behind unit to accommodate cables and connectors. © 2015 Episode® © 2015 Episode®...
-
Page 6: Wall Mount Installation
WARNING: Do not stack anything on top of the amplifier. Plenum Placement The ECA-70VMINI-60W amplifier meets UL 2043 requirements for heat and smoke release. It can be installed in the plenum space, such as in the ceiling, out of sight. - Page 7 1-GND 2-HOT+ Hot + Right 3-COLD- Cold ‒ 3.5mm stereo Use a 3.5mm stereo audio cable or customize the length of the cable, following the pinout below. L (+) R (+) L-/R- ( ) © 2015 Episode® © 2015 Episode®...
-
Page 8: Speaker Outputs
Connect a Control Systen with IR as shown above. RS-232 Port Configuration The ECA-70VMINI-60W amplifier receives control data on the “Rx” pin and transmits control data on the “Tx” pin of the screw-down terminal serial port at the back of the amplifier. The connection cable between the amplifier and the control... -
Page 9: Save Configurations
• Auto ON/OFF Enabled Firmware Update The ECA-70VMINI-60W amplifier may be serviced for firmware updates via a USB memory stick pre-loaded with firmware which is also available on the product page’s support tab. Please call Tech Support if you are in need of assistance. -
Page 10: Troubleshooting
page | 10 TROUBLESHOOTING Amplifier will not turn on. 1. Disconnect all sources and speakers and leave (Amplifier Status LED is only power connected. off) 2. Check the LED on the power supply. 2.1. If power LED is off, check AC power cord and the fuse (Refer to item C on page 2.2. -
Page 11: Specifications
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. © 2015 Episode® © 2015 Episode®... -
Page 12: Year Limited Warranty
SIDE WARRANTY 2-Year Limited Warranty Episode® amplifiers have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified or disassembled.