Festo VTEM Operating Instructions Manual

VTEM
Motion Terminal
Operating instructions
8137053
2020-05c
[8137055]
Translation of the original instructions
© 2020 all rights reserved to Festo SE & Co. KG
GOOGLE CHROME ® , FIREFOX ® , INTERNET EXPLORER
registered trademarks of the respective trademark owners in certain countries.
1

About this document

1.1 Applicable Documents
All available documents for the product è www.festo.com/sp.
Document Product
Assembly instructions CPX, VTEM
Manual VTEM
Manual VTEM-MA...
Manual CPX terminal
Application note VTEM
Tab. 1 Documentation on the product
1.2

Product version

This document refers to the following product versions:
Product Version
VTEM-... Motion Terminal VTEM from revision 01
CTMM-S1-C Controller of the Motion Terminal VTEM from revision 01
Firmware Firmware of the Controller CTMM from version 4.16.0
VEVM-S1-27-... Valve for Motion Terminal VTEM from revision 01
CTMM-S1-D-8E-M8-3 Digital input module for Motion Terminal VTEM from revision 02
CTMM-S1-A-8E-A-M8-4 Analogue input module for Motion Terminal VTEM from revision 02
Browser 1) – Firefox from version 38 (recommended)
– Chrome from version 64
– Internet Explorer from version 11
– Microsoft Edge from version 38
1) Use current version.
Tab. 2 Product version
The product version can be identified from the product labelling or with the help
of appropriate software from Festo.
Appropriate software for determining the product version can be found in the
Festo Support Portal è www.festo.com/sp.
Information on using the software can be found in the integrated Help function.
There may be an updated version of this document for these or later product ver-
sions è www.festo.com/sp.
1.3

Product labelling

The product labelling is explained in the product manual
è 1.1 Applicable documents.
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
8137053
® , MICROSOFT EDGE ® are
Contents
–
System, function, parameterisation
Motion app - function - parameterisation
System, description
Various contents
è www.festo.com/sp è VTEM è Expert
knowledge
2

Safety

2.1

Safety instructions

– Observe product labelling.
– Before working on the product, switch off the power supply and secure it
against being switched on again.
– In the power-free status (normal position), compressed air may be trapped
between the air ports and connected drives.
– Store the product in a cool, dry, UV-protected and corrosion-protected envir-
onment. Ensure that storage times are kept to a minimum.
– Comply with the handling specifications for electrostatically sensitive devices.
– Observe tightening torques. Unless otherwise specified, the tolerance is
± 20 %.
2.2

Intended use

The product is intended for controlling pneumatic drives and for implementing
motion tasks (Motion Apps).
The product may only be used as follows:
– Use only in an industrial environment: outside industrial environments, e.g.
in commercial and mixed-residential areas, action to suppress interference
may have to be taken.
– Use exclusively in combination with modules and components that are certi-
fied for the specific product variant and have been tested and approved by
Festo.
– Use in technically perfect original status without unauthorised modifications.
Only the conversions or modifications described in this and the further applic-
able documents are permitted.
2.3

Training of skilled personnel

Installation, commissioning, maintenance and disassembly should only be con-
ducted by qualified personnel.
The specialized personnel must be familiar with the installation and operation of
electrical and pneumatic control systems.
2.4

UL/CSA Certification

In combination with the UL inspection mark on the product, the information in this
section must also be observed in order to comply with the certification conditions
of Underwriters Laboratories Inc. (UL) for USA and Canada.
UL approval information
Product category code
File number
Considered standards
UL mark
Tab. 3
Only for connection to a NEC/CEC Class 2 supply.
WARNING!
The unit shall be supplied by a power source which fulfils the requirements on a
limited-energy circuit in accordance to IEC/EN/UL/CSA 61010-1 or on a Limited
Power Source (LPS) in accordance to IEC/EN/UL/CSA 60950-1 or IEC/EN/UL/CSA
62368-1 or a Class 2 circuit in accordance to NEC or CEC.
3

Further information

– Accessories è www.festo.com/catalogue.
– Spare parts è www.festo.com/spareparts.
4

Service

Contact your regional Festo contact person if you have technical questions
è www.festo.com.
5

Product overview

The product is a component of a CPX terminal, forms its pneumatic side, and is a
platform for execution of Motion Apps.
QUYX, QUYX7
E322346
UL 61010-1
CAN/CSA C22.2 No. 61010-1