Advertisement
Addi Bedside Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
A
B
C
D
bolt
dowel
screw
locking
x4
x6
x10
nut x6
L
K
M
Allen
screw
nut
x4
x4
key x1
WARNING:
Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that different wall materials may require different fixing
devices from those supplied.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
E
F
G
screw
slide
slide
slide
x20
rail x2
rail x2
rail x2
Q
N
O
P
plastic
small
small
long
bolt
locking
glide x4
Allen
x8
nut x8
bolt x 4
Hardware Supplied
Phillips & Flathead screwdrivers
and hammer required
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
J
H
I
slide
wedge
x4
rail x2
R
S
screw
big
x8
dowel
x4
V
W
X
safety
screw
wall
x1
strap x1
anchor
x1
Wall Strap
Y
Z
wall
washer
screw
x2
x1
1
Advertisement
Table of Contents
Related Manuals for Mocka Addi Bedside Table
Summary of Contents for Mocka Addi Bedside Table
- Page 1 Phillips & Flathead screwdrivers and hammer required For quicker assembly, we recommend the use of a power drill on a low-speed setting. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 2 Attach 2x slide rail (F) and 2x slide rail (G) to panels [3] and [4] as shown with 12x screws (E). Tighten with a screwdriver. Insert 2x bolts (C) into panels [3] and [4]. Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 3 Attach panel [4] and panel [3] to panel [1] with 4x dowels (A) and secure with 2x locking nuts (D). Tighten with a screwdriver. secure with 4x locking nuts (D). Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 4 Attach legs [7] to panel [2] with 4x big dowels (S) and 4x nuts (L) and and [3] to form the back of the unit as shown. secure with 4x Long Allen bolts (Q). Tighten with an Allen key (M). mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 5 Tighten with a screwdriver. Slide panel [12] along the grooves between to the legs [7] using a hammer as shown. the panels [10] and [11] to form the base of the drawer. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 6 Attach slide rail (I) and slide rail (H) to the underside as shown. Ensure the drawers slide easily along the rails. of the side panels as shown. Secure with 4x screws (E) and tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 7 Fasten to the wall using 1x washer (Z) , 1x wall anchor (X) and 1x screws (W). Tighten with a screwdriver. 1x wall screw (Y). Ensure unit is balanced and steady before use. You're done, enjoy! mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Need help?
Do you have a question about the Addi Bedside Table and is the answer not in the manual?
Questions and answers