Table of Contents
Advertisement
Quick Links
Nava Bedside Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
A
B
C
dowel
long
bolt
x12
x6
screw
x14
J
K
L
wedge
hinge
bolt
x4
x2
x4
WARNING:
Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that different wall materials may require different fixing
devices from those supplied.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
D
F
E
locking
cover
screw
bracket
nut x6
x1
x1
M
N
O
P
washer
Cover
seal
screw
x6
x1
x3
x4
Hardware Supplied
Phillips & Flathead screwdrivers
and hammer required
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
G
H
I
screw
screw
x8
x16
x4
Q
R
Allen
plastic
glide x4
key x1
V
W
X
safety
screw
wall
x1
strap x1
anchor
x1
Wall Strap
Y
Z
wall
washer
x2
screw
x1
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mocka Nava Bedside Table
Summary of Contents for Mocka Nava Bedside Table
- Page 1 Phillips & Flathead screwdrivers and hammer required For quicker assembly, we recommend the use of a power drill on a low-speed setting. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 2 Insert 6x bolts (C) into panel [1], and tighten with a screwdriver. Attach 1x bracket (E) to panel [5] and secure with 2x screws (P). Tighten with a screwdriver. Place 1x cover (F) over bracket (E) as shown. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 3 Slide panel [6] down along the grooves between the side panels [3] and [4]. locking nuts (D) and tighten with a screwdriver. Insert 6x covers (N) into the holes of panels [3] ,[4] and [5]. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 4 Attach panel [2] to the unit with 6x dowels (A), and secure with 6x long Attach panels [9] to panels [7] and [8] with 16x screws (H). screws (B). Tighten with a screwdriver. Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 5 Attach Legs [10] to panels [9] with 4x washers (M) and 4x bolts (L). screws (B). Tighten with a screwdriver. Tighten with the Allen key (Q). Attach 4x plastic glides (R) to the legs using a hammer as shown. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 6 (K) with 4x screws (G) as shown. Tighten with a screwdriver. If the door is not catching or sitting flush, twist the end of the cover (F) until it catches on the seal (O). mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 7 (V) to the wall using 1x screw (Y), 1x wall plug (X) and of the unit as shown using 1x washer (Z) and 1x screw (W). Tighten with a 1x washer (Z). Tighten with a screwdriver. You’re done, enjoy! screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Need help?
Do you have a question about the Nava Bedside Table and is the answer not in the manual?
Questions and answers