Furuno NavNet TZtouch TZT 9 Setup Procedure
Flir camera setup procedures
Hide thumbs
Also See for NavNet TZtouch TZT 9:
- Operator's manual (291 pages) ,
- Installation manual (52 pages) ,
- User handbook manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for Furuno NavNet TZtouch TZT 9
Summary of Contents for Furuno NavNet TZtouch TZT 9
- Page 1 Model: /14/BB Model: TZTL - 12F/15F TZT2BB FLIR Camera Setup Procedures -IP Camera Type - FOR COMPOSITE OUTPUT FLIR UNITS: Please see our other support document (NavNet TZtouch and TZtouch2 FLIR camera setup...
- Page 2 INDEX Integration with FLIR M - Series Network Overview Setting up FLIR M - Series (IP Camera Type) 3.1. Assig ning Static IP Address Setting up NavNet TZtouch and TZtouch2...
-
Page 3: Network Overview
3. Setting up FLIR M-Series (IP Camera Type) Static IP addresses should be assigned to the FLIR M-Series camera and JCU-3 to match with the NavNet TZtouch and TZtouch2 network. Only properly configured units should be placed on the Furuno Ethernet. M-Series... - Page 4 Choose an address that isn’t already in use. (Example provided in the earlier table). The IP address of JCU should be 172.31.xxx.xxx. The recommended IP addresses is shown in the prior table. You must avoid duplication with the IP addresses of FURUNO Ethernet sensors. For detailed setup, follow the steps below. Getting Started – Setting up a PC (1) Connect a PC to the FLIR M-Series network.
- Page 5 (3) Once the PC is in the same network domain as the M-Series camera and JCU, you will be able to see the M-Series camera and JCU icons under [Network] (Windows 7 and later). Host names are shown as device names. In this example, [A80438 0770003] is JCU-3 and [E70354 0685135] is M232.
- Page 6 (7) Scroll down to the bottom of the page and click [Save]. (8) Restart the network or restart the camera by recycling the power. Note: You will not be able to access the M-Series camera configuration page anymore after changing its IP address unless the IP address and subnet mask of the PC is changed in step (14).
- Page 7 (11) In the [JCU] page, set the [Camera Selection Mode] to [Auto] and click [Save ini]. (12) In the [NETWORK] page, set the IP address mode, IP addres, and subnet mask as follows. [Mode]: [Static] [IP Address]: [172.31.200.100] (any IP of 172.31.200.xxx without duplication with others) [Netmask]: [255.255.0.0] (13) Click [Save] and [Reboot].
- Page 8 Adjusting the PC’s IP Address to a New Domain (14) After changing the IP address of the M-Series camera and JCU, assign the PC with an IP address of 172.31.xxx.xxx and subnet mask of 255.255.0.0 to match with the new domain. In this example, the IP address 172.31.100.100 and subnet mask 255.255.0.0 are assigned as shown at right.
- Page 9 (17) Select the camera and click [Add -->]. (18) See that the [Camera Connect] section shows the selected camera model.
- Page 10 4. Setting up NavNet TZtouch and TZtouch2 After the FLIR M-Series setup is complete, the TZT9/14/BB and TZTL12F/15F should be set to detect the camera. The procedure is described with screenshots as shown from a TZTL15F with v6.21 software. (1) Access [Home] – [Settings] – [Camera]. (2) Tap [FLIR Installation].
- Page 11 (5) Set the [Video Source] to [IP CAMERA 1]. (or of the corresponding IP camera that you used the address of) You may adjust the setting options related to FLIR M-Series controls are available at the bottom of the FLIR Installation menu. Compatibility is subject to change.
Need help?
Do you have a question about the NavNet TZtouch TZT 9 and is the answer not in the manual?
Questions and answers