Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Furuno FIP-460
Summary of Contents for Furuno FIP-460
- Page 1 FIP-460 IP Camera Installation Guide FURUNO USA, INC. www.furuno.com...
-
Page 2: Warnings & Important Product Information
Ensure suitably rated circuit breakers / fuses death. Furuno cannot be held liable for any incidental, spe- are used in the installation of the product. Never switch on cial, indirect, or consequential damages whether resulting power until the power connections are correctly terminated. -
Page 3: Table Of Contents
Table of Contents Introduction.....1 Key Features Contents of Package Power and Planning..2 Camera Overview.....3 Installation......4 How to Install a....5 Waterproof RJ45 Jacket Connecting to Ethernet Connecting to a....6 TZtouchXL MFD Network Connection Diagrams..7 Troubleshooting Product Dimensions..8 Specifications Worldwide Warranty ..9 for Pleasure Boats (Except North America) Warranty .......10... -
Page 4: Introduction
Thank you for purchasing the FIP-460 IP Camera from Furuno. This user manual is designed to be a reference for the installation and setup of your camera. The FIP-460 IP Camera is ONVIF compliant. In addition to Furuno TZtouchXL MFDs, it may also be viewed on ONVIF compliant hardware. -
Page 5: Power And Planning
Power over Ethernet (PoE) is a system that allows electrical power to be sent via a single ethernet connection. This means that the ethernet cable can provide both power and data to the FIP-460. Optional PoE injector is part # MCU-PWR-INJ Important: If the camera is using PoE for power, do not connect the camera’s direct DC power conenction. -
Page 6: Camera Overview
Camera Overview TIP! It is strongly advised that the camera is powered up and connected to a TZtouchXL MFD to check the desired field of view prior to drilling any holes and mounting the camera in place. Mounting considerations: When choosing a mounting location, keep in mind the following points: •... -
Page 7: Installation
Installation Ensure the camera’s power supply is connected via a suitably rated fuse or circuit breaker. Switch off the power supply while installing the camera. Step 1 Position base at desired mounting position and mark off screw hole and cable entry positions through the mounting surface. -
Page 8: How To Install A
How to Install the Waterproof RJ45 Jacket When installing in an external location, or any location that will be prone to harsh weather, it is important that the waterproof RJ45 connector (supplied) is used to protect the camera connections. Description Part No Camera Network Socket O-ring Seal... -
Page 9: Connecting To A
Connecting the FIP-460 to a TZtouchXL MFD Network TIP! You can connect a max of 8 x FIP-460 IP cameras to a TZtouchXL network. Take this opportunity to change the name of the FIP-460 FIP-460 IP cameras are shipped with their IP address set camera that was just added to the Camera List. -
Page 10: Connection Diagrams
Sample Connection Diagrams Cameras Powered by PoE Hub The FIP-460 IP Camera can be powered by PoE from a PoE injector or PoE Switch or via a direct +12vdc connnection to the 1.5mm DC jack*. * It is also possible to hardwire this connection by cutting off the DC jack and making a direct connection to the red (+12vdc) and black (–) wires.18 gauge wires are recommended for power. -
Page 11: Product Dimensions
Product Dimensions Specifications Sensor 1/4” CMOS Sensor Resolution Variable - 2304 x 1296 (3MP) Max Interface RJ45 10/100 Base T Ethernet Video H.264 Codec / Dual Stream Processing Protocols / TCP/UDP/HTTP/Multicast/UPnP/ Video Format NTP/RTSP/ONVIF ONVIF Profile S v2.4 Bitrate VBR / CBR 32kbps ~ 8Mbps 6 x 850nm Infra-Red - Illumination 10-meter Range... -
Page 12: Warranty Registration
6. Warranty Limitations For products purchased outside of your country please When a claim is made, FURUNO has a right to choose contact the national distributor of Furuno products in the whether to repair or replace the product. -
Page 13: Warranty
24 months from installation date provided the work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius of 50 miles of the shop location. - Page 14 FURUNO USA Inc. 4400 NW Pacific Rim Blvd Camas, WA 98607 Telephone: (+1) 360-834-9300 www.FurunoUSA.com www.furuno.com...
Need help?
Do you have a question about the FIP-460 and is the answer not in the manual?
Questions and answers