Shipping Inspection; Electrostatic Discharge (Esd) Precautions; To The Installer - Maytag Amana MEC96 Series Installation Instructions Manual

H
EATING UNIT SHOULD NOT BE UTILIZED WITHOUT REASONABLE
, ,
ROUTINE INSPECTION MAINTENANCE AND SUPERVISION
BUILDING IN WHICH ANY SUCH DEVICE IS LOCATED WILL BE VACANT
CARE SHOULD BE TAKEN THAT SUCH DEVICE IS ROUTINELY INSPECTED
MAINTAINED AND MONITORED
MAYBE EXPOSED TO FREEZING TEMPERATURES AND WILL BE VACANT
-
ALL WATER BEARING PIPES SHOULD BE DRAINED
,
BE PROPERLY WINTERIZED AND THE WATER SOURCE CLOSED
EVENT THAT THE BUILDING MAY BE EXPOSED TO FREEZING
TEMPERATURES AND WILL BE VACANT
SHOULD BE DRAINED AS WELL AND
SOURCES SHOULD BE UTILIZED
T
O PREVENT POSSIBLE PROPERTY DAMAGE
DEATH DUE TO ELECTRICAL SHOCK
PROTECT THE ELECTRICAL COMPONENTS FROM WATER
Drain trap must be primed at time of installation. Trap is
internally partitioned; add water to both inlet ports until
water appears at both sides of the outlet opening. Failure
to prime trap at time of installation may have a negative
effect on combustion quality and pressure switch action.

Shipping Inspection

All units are securely packed in shipping containers tested ac-
cording to International Safe Transit Association specifications.
The carton must be checked upon arrival for external damage.
If damage is found, a request for inspection by carrier's agent
must be made in writing immediately.
The furnace must be carefully inspected on arrival for damage
and bolts or screws which may have come loose in transit. In
the event of damage the consignee should:
1. Make a notation on delivery receipt of any visible damage
to shipment or container.
2. Notify carrier promptly and request an inspection.
3. With concealed damage, carrier must be notified as soon
as possible - preferably within five days.
4. File the claim with the following support documents
within a nine month statute of limitations.
• Original or certified copy of the Bill of Lading, or
indemnity bond.
• Original paid freight bill or indemnity in lieu thereof.
• Original or certified copy of the invoice, showing trade
and other discounts or reductions.
• Copy of the inspection report issued by carrier's
representative at the time damage is reported to
carrier.
The carrier is responsible for making prompt inspection of
damage and for a thorough investigation of each claim. The
distributor or manufacturer will not accept claims from dealers
for transportation damage.
WARNING
. I
F THE
.
IN THE EVENT THAT THE BUILDING
,
THE BUILDING SHOULD
,
ANY HYDRONIC COIL UNITS
, ,
IN SUCH CASE ALTERNATIVE HEAT
.
WARNING
,
PERSONAL INJURY OR
,
THE FURNACE MUST BE LOCATED TO
.
S
,
HOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAIL TO SHUT OFF
TURN OFF THE MANUAL GAS SHUTOFF VALVE EXTERNAL TO THE
FURNACE BEFORE TURNING OFF THE ELECTRICAL SUPPLY
,
,
,
P
OSSIBLE PROPERTY DAMAGE
,
FIRE EXPLOSION
.
IN THE
OR CARBON MONOXIDE MAY RESULT FROM IMPROPER INSTALLATION
REPAIR OPERATION

Electrostatic Discharge (ESD) Precautions

NOTE: Discharge your body's static electricity before touching
unit. An electrostatic discharge can adversely affect electrical
components.
Use the following precautions during furnace installation and
servicing to protect the integrated control module from damage.
By putting the furnace, the control, and the person at the same
electrostatic potential, these steps will help avoid exposing
the integrated control module to electrostatic discharge. This
procedure is applicable to both installed and non-installed
(ungrounded) furnaces.
1. Disconnect all power to the furnace. Do not touch the
integrated control module or any wire connected to the
control prior to discharging your body's electrostatic
charge to ground.
2. Firmly touch a clean, unpainted, metal surface of the
furnaces near the control. Any tools held in a person's
hand during grounding will be discharged.
3. Service integrated control module or connecting wiring
following the discharge process in step 2. Use caution
not to recharge your body with static electricity;
(i.e., do not move or shuffle your feet, do not touch
ungrounded objects, etc.). If you come in contact with
an ungrounded object, repeat step 2 before touching
control or wires.
4. Discharge your body to ground before removing a new
control from its container. Follow steps 1 through 3 if
installing the control on a furnace. Return any old or
new controls to their containers before touching any
ungrounded object.

To The Installer

Before installing this unit, please read this manual thoroughly to
familiarize yourself with specific items which must be adhered
to, including but not limited to: unit maximum external static
pressure, gas pressures, BTU input rating, proper electrical
connections, circulating air temperature rise, minimum or
maximum CFM, and motor speed connections.
T
O PREVENT PROPERTY DAMAGE
,
FIRE DO NOT INSTALL THIS FURNACE IN A MOBILE HOME
RECREATIONAL VEHICLE
4
WARNING
WARNING
,
PERSONAL INJURY OR DEATH DUE TO
, , ,
SMOKE SOOT CONDENSATION
,
OR MAINTENANCE OF THIS PRODUCT
WARNING
,
PERSONAL INJURY OR DEATH DUE TO
.
,
.
,
ELECTRICAL SHOCK
,
.
, ,
TRAILER OR