Advertisement
Quick Links
INSTRUCTIONS-PARTS LIST
"FLEX" AIRLESS SPRAY GUN
5000 psi (345 bar) MAXIMUM WORKING PRESSURE (without tip guard)
Model 220-956, Series A
The RAC IV
DripLess
4050 psi (279 bar) MAXIMUM WORKING PRESSURE
Includes Reverse-A-Clean
and 517 size SwitchTip . Has two finger trigger.
Model 218-132, Series C
Includes standard tip guard and flat tip.
Has two finger trigger.
A four finger trigger is available.
See page 11.
TABLE OF CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Lists & Drawing
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This manual contains IMPORTANT
INSTRUCTIONS and WARNINGS.
READ AND RETAIN FOR REFERENCE.
Tip Guard has a
IV DripLess
Tip Guard
COPYRIGHT 1983, GRACO INC.
Model 220-956 shown
2
4
4
6
7
11
12
12
307-633
Rev F
Supersedes E
0701
Advertisement
Related Manuals for Graco FLEX A Series
Summary of Contents for Graco FLEX A Series
-
Page 1: Table Of Contents
........GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441... -
Page 2: Warnings
WARNINGS HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating the equipment. FLUID INJECTION HAZARD General Safety Safety Latch Whenever you stop spraying, even for a moment, always set the This equipment generates very high fluid pressure. - Page 3 DO Always wear protective eyewear, gloves, clothing and respirator NOT expose Graco hoses to temperatures above 180 F (82 as recommended by the fluid and solvent manufacturer. C) or below –40 F (–40 C).
-
Page 4: Installation
INSTALLATION NOTE: Numbers and letters in parentheses in the text 1. Guide a grounded fluid hose (A) through the hose correspond to the reference numbers and letters guard (8), and connect the hose to the gun inlet in the drawings and parts list. adapter (13). -
Page 5: Operation
The card contains important treatment information should an injection injury occur. Additional cards CAUTION are available from Graco Inc. at no charge. Openings in the tip guard are designed to reduce paint buildup on the guard when spraying. Any damage to the sharp edges of the openings causes paint to collect at that area. - Page 6 OPERATION Cleaning and clearing the spray tip Flush the gun WARNING WARNING To reduce the risk of a fluid injection or splashing in To reduce the risk of static sparking and splashing, the eyes or on the skin, DO NOT hold your hand, be sure the entire system and the flushing pails are body, or a rag in front of the spray tip when cleaning properly grounded.
-
Page 7: Service
SERVICE WARNING 5. Gently tap the needle (18) from the rear of the hous- ing (19) to push it out the front. To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, Reassembly always follow the Pressure Relief Procedure on page 2 before adjusting, cleaning or repairing the... - Page 8 SERVICE Adjusting the needle See Fig 6. WARNING Proper adjustment of the needle is essential to be sure the trigger safety latch makes the gun inop- erative when engaged. Improper adjustment may allow the gun to be triggered, even with the trigger safety latch engaged, resulting in serious bodily in- jury, including fluid injection and splashing in the eyes or on the skin.
- Page 9 PARTS DRAWING – Model 220–956 **18 **14 **15 TORQUE TO 20–25 ft–lb (27–34 N.m) TORQUE TO 30–40 in–lb (3.4–4.5 N.m) 0709 PARTS LIST Model 220–956, Series A Includes items 1 to 27 NO. PART NO. DESCRIPTION NO. PART NO. DESCRIPTION 203–953 SCREW, lock 214–967**...
- Page 10 PARTS DRAWING – Model 218–132 **18 **14 **15 TORQUE TO 20–25 ft–lb (27–34 N.m) 17** TORQUE TO 30–40 in–lb TIP, order separately (3.4–4.5 N.m) 0710 PARTS LIST Model 218–132, Series C Includes items 1 to 26 NO. PART NO. DESCRIPTION NO.
-
Page 11: Accessories
ACCESSORIES Must be purchased separately . REPAIR KIT 218–143 WRENCH 171–147 Includes fluid needle, diffuser/seat and gasket as Fits all hexes on the gun indicated on pages 8 and 9. 4–FINGER TRIGGER KIT 170–668 Replaces standard 2–finger trigger. NYLON BRUSHES 101–891 3/8”... -
Page 12: Technical Data
OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. tured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.