Care And Maintenance - BQS BCAFIX 123 ST-2 Instruction Manual

8. open the harness buckle (21) (press the red release button) (fig.35)
9. open the left and right velcro (42) on the lower part of the cover (43) and
lift the cover piece to the front. Slide the buckle latches (20) down into the
storage compartments (fig.36,37).
10. Roll the shoulder belts (08) together and place them also into the storage
compartments (fig.37).
11. Repositon the two cover parts to the rear and lock the velcro (42) on the
left and right side of the cover back side (fig.38).
12. Lift the recline handle and pull at the front to fully recline the child seat
(fig.39).
13. Grasp the metal plate (33) from underneath and turn it into a vertical
position.
14. Push upwards and slide the metal plate (33) through the slot (34) .
Remove the harness buckle (fig.40).
7. REFITTING THE 5-POINT HARNESS
1. Squeeze the adjustment handle (12) at the rear of the headrest (07) and
push the headrest into the lowest position (fig.41).
2. open the left and right buttons on the lower part of the cover (43) and lay
the cover piece on the seating area (fig.42).
3. Take the shoulder belts 08 and the buckle latches (20) from the storage
compartment (47) and unroll the shoulder belts (fig.43).
4. Fold back the two cover pieces and close the left and right poppers (42)
on the lower part of the cover (fig.44).
5. Refitting harness buckle (21) and crotch pad. Group 1 (9-18 kg) use the
belt slot closest to the backrest a ,for Group 2 (15-25 kg) use the one
furthest away.
6. Take the harness buckle (21) and hold the metal plate (33) verticaly. Push
it with the narrow side upwards through the belt slot a or b into the seat
shell from above (fig.45).
7. Ensure by looking underneath the seat that the metal plate (33) is in a
horizontal position and check the installation by pulling on the harness
buckle (21) several times (fig.46,47).
8. Guide the two buckle latches (20) together and engage them before
putting them into the harness buckle (21) - this should make a click noise
(fig.48).
CAUtION! The lap belts must not be twisted or swapped.
32
9. Thread the shoulder pads (19) onto the shoulder belts 08 in the correct
orientation as shown ensuring there are no twists. Align the two loops of
the shoulder belts (08) and strap loops of the shoulder pads (19) (fig.49) .
10. Pull the shoulder belts (08) and the strap loops of the shoulder pads (19)
through the slots (40) (fig.50).
11. Pull the strap loops of the shoulder pads (19) onto the plastic extensions
(41) of the shoulder belt height adjuster (10) (fig.51).
tIP: the strap loops of the shoulder pads should be the lower loop.
CAUtION! The shoulder belts (08) must not be twisted or swapped.
12. Take the connecting piece (39) from the provided storage on the back
side of the child seat.
13. Hook the shoulder belts (08) back onto the connecting piece (39) . The left
loop on the left arm of the connecting piece and the right loop on the right
arm (fig.52).

8. CARE AND MAINTENANCE

8.1 Care for the harness buckle
it is vital for the safety of your child that the harness buckle works correctly
Malfunctions of the harness buckle are usually caused by accumulations of
dirt or foreign bodies.
Malfunctions are as follows:
• The buckle latches are ejected only slowly when the red release button is
pressed.
• The buckle latches will no longer lock home (i.e. they are ejected again if
you try to push them in).
• The buckle latches engage without an audible „click".
• The buckle latches are difficult to insert (you feel resistance).
• The buckle only opens if extreme force is applied.
Remedy
wash out the harness buckle so that it functions properly once again:Cleaning
the harness buckle.
1. Follow section 6 to Remove the harness buckle (21) (fig.53,54,55)
2. Soak the harness buckle (21) in warm water with washing-up liquid for at
least an hour. Then rinse and dry it thoroughly.
www.babyqs.com
BCA 123 33