Installation - BQS BCAFIX 123 ST-2 Instruction Manual

soon as you release the adjustment handle (12) the headrest (07) will lock
into place.
3. if the position of headrest (07) is still not fix child, additional adjustment
can be made through the shoulder belt height adjuster (10), as explained
in Section 3.2.
This seat offers a variety of mounting options, the following table indicates
the types of installation for the respective groups:
Fitting vehicle
group
options belt
Method 1 Yes
Group 1
Method 2
Method 1 Yes
Method 2 Yes
Group 2
Method 3 Yes
Method 4 Yes
Method 1 Yes
Group 3
Method 2 Yes
Method 3 Yes

4. INSTALLATION

4.1. GROUP 1 (9-18 kg). With ISOFIT + Top Tether + 5-Point Harness
1. Make sure that the child seat's 5-point harness is installed correctly (see
section 7).
2. Follow the steps in section 3.1(to prepare the iSoFiX.)
3. Follow the steps in section 3.2 (to adjust headrest.)
4. Take the Top Tether and lay it over the child seat.
5. Place the child seat facing in the direction of travel on the vehicle seat.
26
top child user chapter
isoFiX
tether installation
With 5-point
harness
With 5-point
Yes Yes
harness
With 5-point
Yes
harness
Vehicle belt
Yes Vehicle belt
Yes Yes Vehicle belt
Vehicle belt
Yes Vehicle belt
Yes Yes Vehicle belt
6. Grasp the child seat with both hands and slide the two locking arms
(15) firmly into the insert guides (02) until the locking arms engage with a
clicking noise on both sides, the iSoFiX indicator (04) turn green on both
side (figs.8 and 9).
CAUtION! The locking arms are only correctly engaged if both of the safety
buttons (04) are completely green.
7. Push the child seat towards the backrest applying firm, even pressure on
both sides (fig.10).
guide
8. Try to move the child safety seat to makesure it is safely attached and
recheck the green safety buttons (04) to make sure that both of them are
4.1
completely green.
9. Take the top tether and if required, lengthen the belt by pressing the top
4.2
tether brake button to release the strap, pulling to adjust as necessary
(fig.11).
4.3
10. Hook the snap hook (17) into the Top Tether anchoring point recommended
in your vehicle owner's guide (fig.12).
4.4
tIP: Look for this symbol in your vehicle.
4.4
11. To tension the top tether, remove any slack by pulling on the free end of
4.4
strap until it is suitably tightened. The top tether will be properly tightened
when the tension indicator turns completelygreen (fig.13).
4.4
12. Follow the steps in the next section securing your child with 5-point
harness.
4.4
4.1.1. Securing your child with 5-point harness. Group 1
The more snugly the harness fits over your child's body, the better your
4.4
child will be protected. Therefore avoid putting thick clothes on your child
under the belt.
1. open the harness buckle (21) by pressing red button.
2. Press the adjusting button (26) and at the same time pull both shoulder
belts (08) forwards Do not pull on the shoulder pads (19) (fig.14) .
3. Place your child sit down in the child seat.
4. Make sure that your child's back lies flat against the backrest of the child
seat.
5. Guide the two buckle latches (20) together and engage them before
putting them into the harness buckle (21) - this should make a click noise
(fig.15,16,17).
6. Pull on the adjuster strap (09) until the harness lies flat and is close
against your child's body.
www.babyqs.com
BCA 123 27