Removal Of The Child Seat - BQS BCAFIX 123 ST-2 Instruction Manual

clicking noise on both sides, the iSoFiX indicator (04) turn green on both
sides (fig.8,9).
4. Take the top tether and if required, lengthen the belt by pressing the top
tether brake button to release the strap, pulling to adjust as necessary
(fig.11).
5. Hook the snap hook (17) into the Top Tether anchoring point recommended
in your vehicle owner's guide. Look for this symbol in your vehicle (fig.12).
6. To tension the top tether, remove any slack by pulling on the free end of
strap until it is suitably tightened. The top tether will be properly tightened
when the tension indicator turns completely green (fig.13).
• Option B, Install Child seat with ISOFIX connectors only.
1. Place the child seat facing in the direction of travel on the vehicle seat.
2. Grasp the child seat with both hands and slide the two locking arms
15 firmly into the insert guides 02 until the locking arms engage with a
clicking noise on both sides, the iSoFiX indicator (04) turn green onboth
sides (fig.8,9).
• Option C, Install without ISOFIX connectors neither Top tether.
1. Make sure iSoFiX connectors are in shortest position.
2. Have your child sit down in the child seat.
4.4.1 Securing your child using the car seat belt. Group 2/3
2. Pull out the vehicle seat belt and guide it in front of your child to the
vehicle seat buckle (29) . Engage the buckle tongue in the vehicle seat
buckle (29) CLiCK! (fig.25/B)
CAUtION! Do not twist the belt.
3. Place the diagonal seat belt section (11) and lap belt section (28) on the
side of the vehicle seat belt buckle (29) under the armrest and into the red
beltguide (23) of the child seat (fig.26).
4. Place the lap belt section (28) on the other side of the child seat in the red
belt guide (23) (fig.27).
5. Guide the diagonal seat belt section (11) into the red belt holder (30) of
the headrest (07) until it lies completely in the belt holder (30) and is not
twisted (fig.28).
6. Make sure that the diagonal seat belt section (11) runs over your child's
shoulder bone, and not in front of his or her neck.
TIP! You can still adjust the height of the headrest (07) again here inthe vehicle.
30
For the safety of your child, before every journey in the car check that...
• the lap belt section (28) runs through the light red belt guides (23) on both
sides of the seat cushion
• the diagonal seat belt section (11) on the side of the vehicle seat belt
buckle (29) also runs through the light red belt guide (23) of the seat
cushion.
• the diagonal seat belt section (11) runs through the dark red belt holder
(30) of the headrest.

5. REMOVAL OF THE CHILD SEAT

1. To release the iSoFiX fastening, squeeze the safety button (M) ,first on
one side, then on the other.
2. open the buckle of the vehicle seat belt and pull out the diagonal from
lock-off.
3. To release the Top Tether anchoring, loosen the belt by pressing the brake
button of the adjuster. Then take the snap hook out of the anchoring
point.
4. Push the iSoFiX locking arms back into the seat shell.
6. REMOVING THE 5-POINT HARNESS
1. Loosen the 5-point harness 38 of the child seat as much as possible
(fig.29).
Back side of the child seat:
2. Press the button of the shoulder belt height adjuster (10) at the rear of
the seat shell and tilt the shoulder belt height adjuster (10) towards you
(fig.30).
3. Move the shoulder belt height adjuster (10) into the top position and fix
the position by releasing the button of the shoulder belt height adjuster.
4. Loosen the 5-point harness (38) of the child seat as much as possible.
Unhook the shoulder belts 08 on the back side of the child seat from the
connecting piece (39) (fig.31) .
5. Snap the connecting piece 39 in the provided storage (fig.32).
6. Slide the belt loops off of the plastic extensions (41) of the shoulder belt
height adjuster (10) (fig.33).
Front side of the child seat:
7. Pull below both, the shoulder pads 19 and the two shoulder belts (08) to
the front through the slots (40) (front side of the child seat) (fig.34).
www.babyqs.com
BCA 123 31