Low Battery Warning; Operating Power - ADJ PinPoint Gobo COLOR User Instructions

PinPoint Gobo COLOR
2.5 Do Not Expose the Battery to water or liquids
Never soak/drop the batteries in liquids such as water, seawater,
drinks such as soft drinks, juices, coffee or other.
2.6 Battery Replacement
For battery replacement please contact ADJ customer support (800)
322-6337.
2.7 Do Not use a damaged Battery
The battery could be damaged during shipping, caused by shock.
Should the battery be found damaged, including damages to the
plastic casing of the battery, deformation of the battery package,
smelling of an electrolyte, or leakage of the electrolyte gel, or other,
DO NOT use the battery. A battery with a odor of electrolyte or a gel
leakage should be placed away from fire to avoid fire or explosion.
3. Battery Storage
When storing the battery, it should be stored at room temperature,
with a charge of at least 50%. We recommend that during long peri-
ods of storage that the battery be charged every 6 months. Doing
this will prolong the life of the battery and will also make sure that the
battery charge does not fall below the 30% mark.
4. Other Chemical Reaction
Because batteries utilize a chemical reaction, battery performance
will deteriorate over time even if stored for a long period of time
without being used. In addition, if the various usage conditions such
as charge, discharge, ambient temperature, etc. are not maintained
within the specified ranges, the life expectancy of the battery maybe
shortened or the device in which the battery is used may be damaged
by electrolyte gel leakage. If the batteries cannot maintain a charge
for long periods of time, even when they are charged correctly, this
may indicate it is time to change the battery.
5. Battery Disposal
Please dispose of battery according to local regulations.
ADJ Products, LLC - www.adj.com - PinPoint Gobo COLOR User Manual Page 6
Battery Precautions PinPoint Gobo COLOR
Full On Mode, 3.3W Mode, & Energy Saving Mode:
The PinPoint Gobo COLOR has 3 LED modes; full on mode, 3.3W
mode, and energy saving mode. When the PinPoint Gobo is set into
energy saving mode, it will decrease the LED brightness gradually
when the battery life is less than 80% to extend the battery life.
NOTE: When the unit is using DC power, the energy saving mode
cannot be used.
1. Press the MODE button for 5 seconds to switch between normal
mode, 3.3W mode, and energy saving mode. When all LED's flash
two times, the PinPoint Gobo COLOR is in full on mode. When the
blue LED flashes 5 times the PinPoint Gobo COLOR is in 3.3W mode.
When the green LED flashes 10 times the PinPoint Gobo COLOR is in
energy saving mode.
2. When using the ADJ LED RC2, press the BLACKOUT button for 5
seconds. When all LED's flash two times, the PinPoint Gobo COLOR
is in full on mode. When the blue LED flashes 5 times the PinPoint
Gobo COLOR is in 3.3W mode. When the green LED flashes 10 times
the PinPoint Gobo COLOR is in energy saving mode.
3. When using the UC IR, press the STAND BY button for 5 seconds.
When all LED's flash two times, the PinPoint Gobo COLOR is in full on
mode. When the blue LED flashes 5 times the PinPoint Gobo COLOR
is in 3.3W mode. When the green LED flashes 10 times the PinPoint
Gobo COLOR is in energy saving mode.

Low Battery Warning:

When the battery power gets below 30%, the red & blue LED's
will alternately flash rapidly for 5 seconds each time the power is
switched ON. After the 5 seconds, the unit will function normally. This
is a warning letting you know that you must charge the unit soon.

Operating Power:

There are two ways to supply power to this unit; battery power or DC
power.
• DC Power - To run the unit using DC power, plug the unit into a DC
power source, and put the POWER switch into the ON position.
ADJ Products, LLC - www.adj.com - PinPoint Gobo COLOR User Manual Page 7
Operating Instructions