1. Manuals
  2. Brands
  3. eLine Manuals
  4. Modem
  5. ELC-576ET
  6. Manual

eLine ELC-576ET Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
All trademarks in this manual are properties of their respective owners.
TABLE
1 BEFORE YOU BEGIN ................................................................................................................. 2
1.1 Features................................................................................................................................ 2
1.2 Package Includes .................................................................................................................. 3
1.3 Minimum System Requirements ............................................................................................. 3
2 HARDWARE INSTALLATION................................................................................................... 4
2.1 Connection Diagram ............................................................................................................. 4
2.2 LED Indicators ..................................................................................................................... 4
3 SOFTWARE INSTALLATION.................................................................................................... 5
3.4 Software Installation for Linux Red Hat 6.0 ......................................................................... 14
4. COMMAND REFERENCE ....................................................................................................... 15
4.1 AT Commands..................................................................................................................... 15
4.2 Dial Modifiers.................................................................................................................... 22
4.3 Commands Not Preceded By AT ......................................................................................... 23
4.4 S Register Reference ........................................................................................................... 23
5. MODEM REFERENCE............................................................................................................. 30
5.1 Troubleshooting .................................................................................................................. 30
5.2 Result Codes ....................................................................................................................... 30
5.3 Application Examples.......................................................................................................... 31
APPENDICES ................................................................................................................................ 34
Appendix A: Caller ID Commands (Optional) ........................................................................... 34
Appendix B: Technical Specifications........................................................................................ 35
Appendix C: Quick Reference.................................................................................................... 36
Appendix D: Glossary............................................................................................................... 38
Appendix E: ASCII CODE TABLE ........................................................................................... 39
Appendix F: FCC/DOC REQUIREMENTS................................................................................ 40
®
95 .................................................................................. 5
®
98 .................................................................................. 7
®
NT................................................................................ 13

Advertisement

Table of Contents
loading

Summary of Contents for eLine ELC-576ET

  • Page 1: Table Of Contents

    All trademarks in this manual are properties of their respective owners. TABLE 1 BEFORE YOU BEGIN ......................... 2 1.1 Features..........................2 1.2 Package Includes ........................3 1.3 Minimum System Requirements ..................... 3 2 HARDWARE INSTALLATION....................4 2.1 Connection Diagram ......................4 2.2 LED Indicators ........................

  • Page 2: Before You Begin

    EFORE EGIN 1.1 Features These Fax/Data Modems combine the features of a 56000(receive only)/33600/28800/14400/9600 bps data modem and a 14400/9600 bps FAX modem. Your new Fax/Data Modem gives your personal computer the ability to send and receive FAX messages over the telephone line like a standard FAX machine.

  • Page 3: Package Includes

    1.2 Package Includes Before installation, please check the items of your package. The package should include the following items: • The External Modem • Quick Installation ® ® ® • Installation Disk (including drivers for Windows 95 /Linux Red Hat 6.0 If any of the above items are missing, contact your supplier as soon as possible.

  • Page 4: Hardware Installation

    ARDWARE NSTALLATION 2.1 Connection Diagram The serial products of the external modems distinguish each other with voice function and phone jack. The Diagram below illustrates the typical external modem connection: 2.2 LED Indicators After hardware installation, turn on the modem and your PC, the PWR, HS, and MR LEDs should be lit.

  • Page 5: Software Installation

    OFTWARE NSTALLATION After hardware installation, power on your PC and follow the instructions to install the drivers for the modem card. ® 3.1 Software Installation for Windows Step 1: After installing the modem card into your PC, power on your PC and start Windows95. The Wizard box appears announcing the detecting of a new hardware.
  • Page 6 Windows will find the location of driver; click “Finish”. Step 4: If your modem does NOT support voice function, just ignore the steps below. Again, Windows will detect a voice device; click “Next”. Step 5:...

  • Page 7: Software Installation For Windows 98

    Step 6: Click “Other Locations” and open the driver file from “Win95_98” folder in the disk drive; then click “OK”. Step 7: Windows will find the location of driver; click “Finish”. ® 3.2 Software Installation for Windows Step 1: After installing the modem card into your PC, power on your PC and start Windows 98. The Wizard box appears announcing the detecting of a new hardware.
  • Page 8 Step 2: With “Search for the best driver for your device” checkbox selected, click “Next”. Step 3: Check “Specify a location”, and click “Browse”. Browse and open “ Win95_98” subdirectory from your floppy drive. Click “OK”. Then click “Next”.
  • Page 9 Step 4: Windows will find the driver file for the device; click “Next”. Step 5: Click “Finish” to complete installing. If your modem does NOT support voice function, just ignore the steps below.
  • Page 10 Step 6: Again, Windows will detect a voice device; click “Next”. Step 7: With “Search for the best driver for your device” checkbox selected, click “Next”.
  • Page 11 Step 8: Check “Specify a location”, and click “Browse”. Browse and open “ Win95_98” subdirectory from your floppy drive. Click “OK”. Then click “Next”.
  • Page 12 Step 9: Windows will find the driver file, and click “Next”. Step 10: Click “Finish” to complete the installation.

  • Page 13: Software Installation For Windows Nt

    ® 3.3 Software Installation for Windows Step 1: After hardware installation, power on your modem and then start Window NT4.0. Double click “My Computer” icon; then double click “Control Panel” icon. In “Control Panel” box, find and double click “Modems” icon. Step 2: In “Install New Modem”...

  • Page 14: Software Installation For Linux Red Hat 6.0

    3.4 Software Installation for Linux Red Hat 6.0 Step 1: After hardware installation, power on your modem and start Linux RedHat. Step 2: Click “System Menu” button and select “System”. Step 3: Click“Control Panel”, and then click“Modem Configuration”button. Step4: At the path /dev, enter the single command line: setserial tty-number uart 16550A irq IRQ- number port I/O-address For example: setserial ttyS2 uart 16550A irq 5 port 0xe400 Step 5: At the path /dev, remove the default modem link, and then link the modem to the tty you...

  • Page 15: Command Reference

    4. C OMMAND EFERENCE This chapter includes all commands, S-Registers supported by the modem. Before using the commands, make sure your communications software package provides the function of operating the modem through its interna1 commands. If your software does not support the function, ignore Chapter 4 and 5.
  • Page 16 contained in the following section. The D command without a dial string is usually used to switch from voice conversation to data communication or to call a remote modem in leased- line operation mode. Command Echo E0/E Disables command echo. Enables command echo.
  • Page 17 O0/O Enters on-line data mode without a retrain. Handling is determined by the Call Establishment task. Generally, if a connection exists, this command connects the DTE back to the remote modem after an escape (+++).(Default) Enters on-line data mode with a retrain before returning to on-line data mode. Enters on-line data mode with a rate re-negotiation before returning to on-line data mode.
  • Page 18 If the modem is in facsimile mode (+FCLASS=1) , the only message sent to indicate a connection is CONNECT without a speed indication. X0/X CONNECT result code is given upon entering online data state. Dial tone and busy detection are disable. CONNECT<text>...
  • Page 19 &G2 Select 1800Hz-guard tone. &Kn DTE/Modem Flow Control Determines how the modem controls the flow of data between the local DTE and the modem. When the modem terminal buffer is nearly full, the modem will either send an XOFF or drop CTS to stop the data flow.
  • Page 20 &W Store the Current Configuration to Nonvolatile RAM &W0/&W Writes the current active configuration to profile 0 in nonvolatile RAM. (Default) &W1 Writes the current active configuration to profile 1 in nonvolatile RAM. &Yn Select the Default Profile &Y0/&Y Uses profile 0 on power-up. (Default) &Y1 Uses profile 1 on power-up.
  • Page 21 *I14 Selects connect speed 45333bps *I15 Selects connect speed 46666bps *I16 Selects connect speed 48000bps *I17 Selects connect speed 49333bps *I18 Selects connect speed 50666bps *I19 Selects connect speed 52000bps *I20 Selects connect speed 53333bps *I21 Selects connect speed 54666bps *I22 Selects connect speed 56000bps (Dafault) *Gn User Abort Selection *G0/*G...

  • Page 22: Dial Modifiers

    Enables or disable data compression negotiation. The modem can only perform data compression on an error-corrected link. Disables data compression. Enables V.42bis/MNP 5.(Default) 4.2 Dial Modifiers This section describes all of the dial modifiers that are used in dial strings. Answer "@", placed after a phone number, this modifier tells the modem to wait for 5 seconds of silence before dialing the next number in the dial string.

  • Page 23: Commands Not Preceded By At

    Command: ATDTS=1<CR> Touchtone Dialing T, placed ahead of a number, tells the modem to dial a number using touchtone dialing. Wait for Dialtone W, placed after a number, tells the modem to wait up to 30 seconds to detect a one-second continuous dialtone before dialing the next number.
  • Page 24 4.4.1 Register Summary Important: The contents of the following registers are for reference. The following chart summarizes your modem's registers: Default Reg.# Range Unit Description 0 - 255 rings Number of rings before auto-answer. 0 - 55 rings Ring count. 0 - 255 ASCII Escape character code.
  • Page 25 Line Termination Character S3 sets the decimal value of the command line and result code terminator character. Pertains to asynchronous operation only. Range: 0 - 127, ASCII decimal. Response Formatting Character S4 sets the decimal value of the character generated by the modem as part of the header, trailer, and terminator for result codes and information text, along with the S3 parameter.
  • Page 26 Range: 1 - 255 seconds. Carrier Detect Response Time S9 determines how long a carrier signal must be present for the modem to confirm it. The longer the response time, the easier it is for the modem to correctly recognize a carrier without mistaking other signals or transient noise on the line as a carrier.
  • Page 27 bit 7 Answer mode. Originate mode. Bit Mapped Options Value Description bit 0 [RESERVED] bit 2 &R0. &R1. &D0. bit 3,4 &D1. &D2. &D3. bit 5 &C0. &C1. bit 6 &S0. &S1. Bit Mapped Options Value Description bit 0,1 Select L0. Select L1.
  • Page 28 forcing the modem back to the asynchronous command mode. During this time, the value for S25 is read in whole seconds. Range: 0 - 255 (0.01 second) RTS to CTS Delay Interval Pertains to synchronous operation only. When CTS tracks RTS (&R0) and the modem detects an ON- to-OFF transition on RTS, this register sets the time delay before the modem turns CTS to ON.
  • Page 29 bit 0,1 *H0. *H1. *H2. *H3. Bit 2 *G0. *G1. Bit 3 *T0. *T1. Bit 4-6 &K0. &K1. &K2. &K3. &K4. &K5. Energy detection threshold This register can use in Call Progress Mode (CPM) for dial tone detection threshold. The default value is 16 This register determine the detection threshold for call progress tone.

  • Page 30: Modem Reference

    5. M ODEM EFERENCE 5.1 Troubleshooting This chapter describes common problems in the installation, configuration and regular usage of your Fax/Data Modem. To test the Fax/Data Modem, a communication software package is needed and the package must include a mode that allows you to operate your Fax/Data Modem by directly issuing internal commands to the modem.

  • Page 31: Application Examples

    BUSY Detected a busy tone after dialing NO ANSWER No ringback or quiet answer was detected. CONNECT 300 x x x x Connection established at 300 bps CONNECT 2400 x x x x Connection established at 2400 bps CONNECT 4800 x x x x Connection established at 4800 bps CONNECT 9600...
  • Page 32 This command line instruct the modem to dial a remote modem through a PBX. The modem first use pulse dialing to dial 9 (the access code of the PBX), wait for outside dial tone, and then use touch tone dialing to dial 002 once a one-second continuous dial tone is detected within 30 seconds, pause for 2 seconds (if S8=2) and then dial 8867128423.
  • Page 33 2. When the person on the other end hears an answer tone from the phone, issues an ATX1D command (X1 to disable the dial tone monitor) to instruct the modem to go off-hook and wait for a carrier. If connection is successful, the CONNECT XXXX result code will be displayed on the screen.

  • Page 34: Appendices

    PPENDICES Appendix A: Caller ID Commands (Optional) +VCIDn - Caller ID (Enables or disables Caller ID.)(for U.S.A) This command only apply to models which support the Caller ID function. +VCID=0 Disables Caller ID.(Default.) +VCID=1 Enables Caller ID with formatted presentation to the DTE. The modem will present the data items in a <Tag><Value>...

  • Page 35: Appendix B: Technical Specifications

    DATE = 0321 TIME = 1405 NMBR = 504551234 NAME = A N OTHER RING RING 2. The following example illustrates the case where the tag of the packet is not recognized by the modem. RING MESG = 06034242431 RING RING Unformatted Form Reporting The modem presents all information and packet control information found in the message.

  • Page 36: Appendix C: Quick Reference

    Operation Maximum download with 28800, 26400, 56000 bps/download and 33600 bps/ 24000, 21600, 19200, 14400, 9600, 4800, 2400 and 1200 bps auto fallback Audio Monitor Built-in speaker, with software-controllable volume control Guard Tone 550/1800 Hz Compliance FCC 15&68 Command Buffer 30 characters Extra Memory 4 x 36 digits...
  • Page 37 Select Word or Digit Result Codes Negotiation Progress Reporting Extended Result Codes Reset &Cn Select DCD Options &Dn DTR Option &F Fetch Factory Configuration &Gn Set Guard Tone &Kn DTE/Modem Flow Control &Mn Communication Mode &Pn Select Pulse Dialing Make/Break Ratio &Rn CTS Option &Sn...

  • Page 38: Appendix D: Glossary

    Touchtone Dialing Wait for Dialtone Repeat Command Escape Appendix D: Glossary ASCII - An acronym for American Standard Code for Information Exchange. ASCII is a seven-bit code which defines 128 standard characters, including control characters, letters, numbers, and symbols. An extra 128 characters comprise the extended ASCII set. Baud Rate - The transmission rate between two serial devices, e.g., modems, fax machines, etc.

  • Page 39: Appendix E: Ascii Code Table

    On-Hook - The condition when the modem has not picked up the telephone line; the telephone is hung On-Line - A carrier signal link with a remote modem has been established; communication is in progress. On-Line State - A modem state in which the modem is connected with a remote modem. Data can be sent or received from the remote modem in this state.

  • Page 40: Appendix F: Fcc/Doc Requirements

    04 EOT 64 d 05 ENQ 65 e 06 ACK & 66 f 07 BEL 67 g 08 BS 68 h 09 HT 69 i 0A LF 2A * 4A J 6A j 0B VT 2B + 4B K 6B k 0C FF 2C , 4C L...
  • Page 41 However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
  • Page 42 F.3 DOC Notice Notice: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user? satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.

Table of Contents