Related Manuals for Hayter LT322
Summary of Contents for Hayter LT322
- Page 1 LT322 / LT324 FITTING KIT INSTRUCTION MANUAL AND PARTS LIST FROM SERIAL NO. 917P001014 (CAB), 919R001001 (FITTING KIT) MANUAL PART NO. 919014 (REV.0.) ISSUE: 21.04.99...
- Page 3 ATTENTION THIS SYMBOL MEANS BE ALERT! YOUR SAFETY IS INVOLVED THIS CAB IS FOR USE ON THE LT322 AND LT324 TURF MOWERS. READ THIS MANUAL BEFORE FITTING THE CAB. IT IS ESSENTIAL THAT OPERATOR'S STUDY IT FOR THEIR OWN SAFETY.
-
Page 4: Table Of Contents
CONTENTS CONTENTS Page No. INTRODUCTION. WARRANTY. SAFETY PRECAUTIONS. 1.6 - 1.7 Training. Preparation. Operation. 1.6 - 1.7 EC CONFORMITY INFORMATION. Noise Levels. EC Declaration of Incorporation. SPECIFICATIONS. PARTS LIST / DELIVERY CHECK LIST - KIT. 1.10 - 1.11 PARTS LIST - CAB. 1.12 - 1.13 CAB GENERAL ASSEMBLY. -
Page 5: Introduction
INTRODUCTION The Cab Code 917P is designed to be fitted to the Hayter LT322 2WD Triple Turf Mower or the LT324 4WD Triple Turf Mower using Fitting Kit Code 919R. This allows the mower to be used on slopes up to a maximum of 22 degrees depending on ground conditions and provides limited safety protection in the event of a roll-over. -
Page 6: Safety Precautions
SAFETY PRECAUTIONS READ THIS MANUAL BEFORE FITTING OR USING THE CAB. IT IS ESSENTIAL THAT OPERATORS STUDY IT FOR THEIR OWN SAFETY. THESE INSTRUCTIONS ARE IN ADDITION TO THOSE CONTAINED IN THE MACHINE OPERATOR’S MANUAL UNLESS OTHERWISE STATED. READ AND UNDERSTAND THE SEPARATE MACHINE OPERATOR’S MANUAL BEFORE ATTEMPTING TO FIT THE CAB. -
Page 7: Operation. 1.6
Continued. Do not use the LT322 or the LT324 Triple Turf Mowers on a slope of more than 19 degrees unless the approved cab is fitted. Do not use the LT322 or the LT324 Triple Turf Mowers on a slope of more than 27 degrees when fitted with the approved cab. -
Page 8: Ec Conformity Information
EC CONFORMITY INFORMATION NOISE LEVELS Operator’s Daily Personal Noise Exposure : HAYTER LIMITED have no control over site conditions, duration of use, state of maintenance or adjustment of the mower. All of these factors will affect the operator’s daily personal noise exposure level - L EP,d... -
Page 9: Specifications
SPECIFICATIONS SPECIFICATIONS Cab Only Fitting Kit Cab Fitted to Machine With Beacon Fitted (with 200mm Cutterheads) LT322 LT324 LT322 LT324 Overall Height 1550mm 2300mm 2300mm 2450mm 2450mm Overall Width 1031mm 2120mm 2120mm 2120mm 2120mm Overall Length 1405mm 2690mm 2690mm 2690mm... -
Page 10: Parts List / Delivery Check List - Kit. 1.10
1.10 1.10 PARTS LIST / DELIVERY CHECK LIST CODE 919R - KIT PARTS LIST Item No. Description Part No. Full Cab - Code 917P CODE 917P Bracket - Cab Support W/A R.H. 919002G Bracket - Cab Support W/A L.H. 919003G Bolt - M16 x 100 ZBH1P100U Washer - M16 Plain... - Page 11 1.11 1.11 PARTS LIST / DELIVERY CHECK LIST CODE 919R - KIT 1D918R02A 1D919R14A 1D918R01A...
-
Page 12: Parts List - Cab. 1.12
1.12 PARTS LIST CODE 917P - CAB 1.12 PARTS LIST Item No. Description Part No. Catch - Over Centre 915045 Window - Floor L.H. 915050 Window - Floor R.H. (Not Illustrated) 915051 Trim - Corner Panel R.H. 915049 Trim - Corner Panel L.H. 915048 Hinge - Door 915046... - Page 13 1.13 1.13 PARTS LIST CODE 917P - CAB...
-
Page 14: Cab General Assembly. 1.14
CAB GENERAL ASSEMBLY INTRODUCTION To assemble the Cab to the LT322 and LT324 you will require Cab Code 917P and Fitting Kit Code 919R. Check that all parts have been correctly supplied. Check against the Delivery Check List on page 1.10-1.11. - Page 15 Drill out the two chassis mounting holes on the front tool box bracket to diameter 10.5mm. Remove and discard the rearmost fuel tank mounting fasteners on each side of the machine. (For early LT322 and LT324 Turf Mowers, refer to page 1.20).
- Page 16 1.16 1.16 CAB GENERAL ASSEMBLY ASSEMBLY Continued. fig. 4. Front 1D919R15A 14. Identify the wiring harness, switch, lens, fuse and cable fig. 5. (Code P Models) ties (items 53, 54, 55, 56, 57). Refer - figs. 5 and 5 Chassis Earth Point (Located beneath L.H.
- Page 17 1.17 1.17 CAB GENERAL ASSEMBLY Continued. ASSEMBLY fig. 5 . (Code S Models) 24. Fit the draught excluder and protection strip (items Chassis Earth Point 33, 34) to the rear cab mount (item 32). Fit the (Located beneath L.H. side of chassis) washer bottle bracket (item 46) with fasteners (items R.H.
- Page 18 350Kg safely), carefully raise the cab frame assembly from the transport frame using suitable lifting 1D919R02A straps as shown in fig. 8. The transport frame should be returned to Hayter Limited for re-use. 31. Carefully align the cab frame assembly with the fig. 9.
- Page 19 1.19 1.19 CAB GENERAL ASSEMBLY ASSEMBLY Continued. 32. Fit the R.H and L.H. front lower trims (items 50, 51) and foam strips (items 52) to the base of the cab frame. Refer - fig.10. 33. Support the weight of the cab with the lifting equipment and rotate the cab frame rearwards to locate onto the rear isolator mounts (items 35).
- Page 20 CAB GENERAL ASSEMBLY ASSEMBLY Continued. Early LT322 and LT324 Turf Mowers will require some hole sizes to be increased and additional holes to be added to enable the cab to be fitted. WARNING: PREVENT ACCIDENTS - Always wear eye protection when drilling.
-
Page 21: Beacon Assembly. 1.21
If a beacon kit is required when a cab is fitted it must be assembled to the cab roof. An optional Beacon Kit (Code 926R) is available from your Hayter dealer and full fitting instructions are included. If a beacon is already fitted to the engine cover of the machine, it must be refitted to the cab roof. - Page 22 18. Rotate the ignition switch to the ‘I’ position. Depress the beacon switch and check that the beacon rotates and flashes correctly. 19. Finally replace the operator platform securing bolts and torque to the correct settings. (Refer to LT322 or LT324 Operators Manual - Code P Models) .
-
Page 23: Beacon Template
1.23 1.23 BEACON ASSEMBLY BEACON TEMPLATE Drill 4 holes as shown Diameter 7.0 - 8.0 mm Diameter 15 - 16 mm Diameter 7.0 - 8.0 mm Diameter 7.0 - 8.0 mm... -
Page 25: Maintenance
1.25 1.25 MAINTENANCE COMMISSIONING THE CAB - Fill the washer bottle with water / windscreen wash fluid. - Operate the windscreen wiper / washer switch and check for correct operation. - Lubricate the door pivot points with grease. - Operate the door mechanism and ensure correct operation. DAILY - Check that all nuts and bolts are secure and in good condition. -
Page 26: To Re-Assemble The Cab
1.26 1.26 MAINTENANCE TO RE-ASSEMBLE THE CAB WARNING - PREVENT ACCIDENTS: The following procedures should be performed with the aid of an assistant. Lower all cutterheads to rest on the ground. Apply the parking brake, switch off the engine and remove the ignition key. Connect up suitable lifting equipment (capable of lifting 350 kg safely) and arrange the lifting straps as shown in fig. -
Page 27: Electrical Wiring Diagram
1.27 ELECTRICAL WIRING DIAGRAM 1.27 R/BU 1D919R03A - Wiper Motor - Switch - Fuse Box - Washer Pump - Beacon BU - Blue BL - Black - Red OR - Orange...