Page 1
So Serve Models Two-Line Display :: Standard or Air Pump :: Counter or Floor Standing SPM-D-XS-TY001 R2 202001...
Page 2
3. Cut stabilizing straps, being careful not to scratch or dent the machine panels. be subject to change. Please check online or contact your local Spaceman distributor for con nued updates and 4. Prepare the area where the machine will be placed, remove packing cardboard from underneath machine, detailed informa on about your Spaceman machine.
Page 3
Circuit Breaker or Wall Receptacle before switching on or plugging in the machine. If you require an alterna ve refrigerant, please SS B call Spaceman Technical Support for a list of compa ble alterna ves for your compressor. 3PH, 1PH,...
Page 4
CAUTION: Always separate O-rings and gaskets from metal parts to prevent damage while washing. For op mal machine performance and many years of efficiency and reliability from your machine, Spaceman recommends cleaning and sani zing the machine and its parts weekly.
Page 5
5. D CAUTION: Never wash parts in a dishwasher. Always hand-wash components with nontoxic, food-safe cleaners. Op on A: Stainless Steel Beater a. Remove beater assembly from cylinder. b. Remove seal from beater assembly. 1. Verify power switches are in the OFF posi on. 2.
Page 6
(Shaded Area) and turn to desired overrun se ng. b. Insert drive sha s into rear shell bearings at the f. Coat air pump drive sha s with Spaceman back of the cylinders, and turn them un l the key lubricant.
Page 7
To be er communicate in the Interna onal arena, symbols have replace words on many of your operator switches. SPACEMAN equipment is designed with these interna onal symbols. CAUTION: Always use food-grade, no-rinse sani zer to sani ze. If warm water is required to dissolve sani zer, allow the solu on me to cool before adding to machine.
Page 8
NOTE: The mix-low lights illuminate when a hopper is low on product mix and automa cally de- Side draw handles dispense product from their respec ve hoppers. The illuminate when machine is filled. middle draw handle twists product from the le and right hoppers. 1.
Page 9
IMPORTANT: IMPORTANT: When the machine will NOT be u lized for several hours, place it in STANDBY mode to conserve electricity and reduce product loss. 1. Viscosity controls how hard ice cream will be. Slightly adjust viscosity during ini al setup and for In STANDBY, product remains below 4 C (40 F) in both the cylinders and hoppers, but will NOT be frozen.
Page 10
2. Adjust hopper temperature warmer (Page 16). 1. Use sufficient food-grade lubricant, and add sufficient lubricant inside drive sha gasket 3. Call Spaceman Technical Support. : STOP 2—M during assembly (Page 9). 2. Replace drive sha gaskets every 1 to 3 months.
Page 11
Dispensing Door Use below 1:1 size comparison chart and explosion diagrams on le page to confirm item, size and loca on of O-rings and seals. 6225 6234 6235 6245 6240 6250 6248 6368 Series 6210 6220 6228 Series 6236 6338 Series 6260 6378 Series 6265 6268 Op onal Parts...
Page 12
Viscosity Viscosity Model Model Viscosity Range Model Range Range 6210-60Hz 6210-50Hz 2.5-3.5A 6210-50Hz W/ Inverter 2-3A 6220-60Hz 3.5-6 A 6220-50Hz 2.5-3.5A 6220-50Hz W/ Inverter 2.5-3.5A 6228-60Hz 2-3.5 A 6218-50Hz 2.5-3.5A 6218-50Hz W/ Inverter 2-3.5A 6228A-60Hz 2-3.5 A 6225-50Hz 3-5A 6225-50Hz W/ Inverter 3-4.5A...
Need help?
Do you have a question about the 6210-60Hz and is the answer not in the manual?
Questions and answers